Sea-doo 2001 GS 5548 Operator'S Manual Download Page 76

Page: 76 / 100

Pre-Season Preparation Chart

NOTE:

It is highly recommended that an authorized Sea-Doo dealer perform the

annual safety inspection and factory campaigns in addition to the pre-season prep-
aration all at the same time.

➀

Before installing new spark plugs, it is suggested to burn the excess BOM-

BARDIER LUBE lubricant or equivalent by starting the engine using the old
spark plugs.

➁

Safety item covered in the annual safety inspection.

OPERATIONS

TO BE

PERFORMED

GENERAL

Lubrication/corrosion protection

Operator

Spark plug replacement

➀

Operator

ENGINE

Exhaust system condition (fasteners, hoses etc.)

Dealer

Counterbalance shaft oil level

(if so equipped)

Dealer

Ignition timing

(RFI models)

Dealer

COOLING
SYSTEM

Inspection of cooling system hoses and components

Dealer

FUEL
SYSTEM

Carburetor adjustment

(carburetor-equipped models)

Dealer

Throttle

➁

and choke

(carburetor-equipped models)

cable inspection/adjustment

Dealer

Fuel filter replacement

(carburetor-equipped models)

Dealer

Fuel injection sensors verification

(RFI models)

Dealer

Fuel system; check valves, lines, fasteners,

pressurization

➁

Dealer

Filler neck, fuel tank and fuel cap condition

➁

Dealer

Flame arrester inspection

➁

Dealer

Fuel tank straps

Operator

Refill fuel tank

Operator

LUBRICATION
SYSTEM

Oil injection pump adjustment

Dealer

Oil filter replacement

Dealer

Oil injection reservoir straps

Operator

Oil injection reservoir filling

Operator

Oil injection pump adjustment and bleeding

Dealer

ELECTRICAL
SYSTEM

Battery condition/charging and reinstallation

Dealer

Battery, starter connections and routing

➁

Dealer

Monitoring beeper

Dealer

Digitally encoded security system

Dealer

STEERING
SYSTEM

Steering system adjustment/inspection

➁

Dealer

PROPULSION
SYSTEM

Shifter system condition and cable adjustment

(if so equipped)

Dealer

VTS (Variable Trim System,

(if so equipped)

)

Dealer

Propulsion system inspection

Dealer

Jet pump oil replacement

Dealer

HULL AND
BODY

Inspection of bailer pick-ups

Dealer

smo2001-002a.book Page 74 Wednesday, June 7, 2000 3:57 PM

www.SeaDooManuals.net

Summary of Contents for 2001 GS 5548





































































































Search results

Summary of Contents for 2001 GS 5548

Reviews:

Sea-doo 2001 GS 5548, Operator'S Manual, Page: 76 / 100

Search results

Summary of Contents for 2001 GS 5548

Reviews: