manualshive.com logo in svg

Sea-doo 2001 GS 5548, Operator'S Manual, Page: 42 / 100

Share
Download
Sea-doo 2001 GS 5548 Operator'S Manual Download Page 42

40

DAILY PRE-OPERATION CHECKS

Some of the following items may not have been previously covered in this guide,
however they will be described in the MAINTENANCE or SPECIAL PROCE-
DURES section. Please refer to these sections to have more detailed information.

WARNING

Only start watercraft once all items have been checked and operate prop-
erly.

WARNING

Safety lanyard should always be removed from its switch prior to verifying
any of the following.

ITEM

OPERATION

✓

Hull

Inspect.

Jet pump water intake

Inspect/clean.

Bilge

Drain. Ensure plugs are secured.

Battery

Inspect tightness of cables and retaining strap.

Fuel tank and oil reservoir

Refill.

Engine compartment

Verify for any fuel leak/odor.

Steering system

Check operation.

Throttle system

Check operation.

Shifter system 

(if so equipped)

Check operation.

VTS 

(if so equipped)

Check operation.

Safety lanyard and engine
start/stop button

Check operation.

Storage compartment covers

Ensure they are closed and latched.

smo2001-002a.book  Page 40  Wednesday, June 7, 2000  3:57 PM

www.SeaDooManuals.net

Summary of Contents for 2001 GS 5548





































































































Reviews:

No comments