background image

14

5. LIMITATIONS OF LIABILITY

This warranty gives you specific rights, and you may also have other legal rights
resulting from the application of mandatory national laws which may vary from
country to country. 

WHERE APPLICABLE, THIS WARRANTY IS EXPRESSLY

GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER WARRANTIES, EX-
PRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

In no event shall BOMBARDIER be liable for special, consequential or incidental
damages, including but not limited to loss of use and transportation costs. Some
country do not allow the exclusion or limitation of incidental or consequential dam-
ages, or limitations on how long an implied warranty lasts, so the above limitation
or exclusion may not apply.
Neither the SEA-DOO International Distributor, the selling local SEA-DOO dealer
nor any other person has been authorized to make any affirmation, representation
or warranty other than those contained in this warranty, and if made, such affirma-
tion, representation or warranty shall not be enforceable against BOMBARDIER or
any other person.
Every SEA-DOO watercraft is sold with the English version of this warranty. A
specific SEA-DOO International Distributor may elect to translate this warranty into
local language, it is then understood and agreed that in the event of any discrepancy
among the two versions, the English version shall prevail.
It is the customer’s responsibility to ensure that the SEA-DOO watercraft complies
with all boating regulations and standards of any country, other than the original
country of sale, where the SEA-DOO watercraft is intended to be used.
BOMBARDIER reserves the right to modify this warranty at any time, being under-
stood that such modification will not alter the warranty conditions applicable to the
SEA-DOO watercraft sold while this warranty is in effect.

6. TRANSFER

If the customer sells the watercraft guaranteed under the present, he shall assign
and transfer this warranty, which shall be valid for the rest of the relevant PERIOD
as defined in section 1 hereinabove, to the new customer.

7. CONSUMER ASSISTANCE

a) In the event of a controversy or a dispute arising in connection with this BOM-

BARDIER INTERNATIONAL LIMITED WARRANTY, BOMBARDIER suggests
that you try to resolve the issue at the dealership level. We recommend discuss-
ing the issue with the authorized dealer's service manager or owner.

b) If further assistance is required, the authorized local SEA-DOO INTERNATIONAL

DISTRIBUTOR’s service department should be contacted in order to resolve the
matter.

c) If the issue has still not been resolved, please submit in writing your complaint to: 

BOMBARDIER RECREATIONAL PRODUCTS
SEA-DOO
INTERNATIONAL SERVICE DEPARTMENT

75, J. A. BOMBARDIER ST.
SHERBROOKE, QC

J1L 1W3
CANADA

© MARCH 1999 Bombardier Inc. All rights reserved.
® Registered trademark of Bombardier Inc. and/or its subsidiaries.

smo2001-002a.book  Page 14  Wednesday, June 7, 2000  3:57 PM

www.SeaDooManuals.net

Summary of Contents for 2001 GS 5548





































































































Reviews: