Sea-doo 2001 GS 5548 Operator'S Manual Download | Manualshive

Page: 70 / 100

background image

68

Locate the electrical box.

Unclip and remove cover of the electri-
cal box.

GS AND GTI MODELS

1. Fuse holder

General Inspection and
Cleaning

Inspection

Check engine compartment for any
damage and fuel/oil injection systems
for leaks. Ensure all hose clamps are
properly secured and no hose is
cracked, kinked or presenting any oth-
er damage.

Inspect muffler, battery, fuel tank and
oil reservoir fastening devices. Visually
check electrical connections for corro-
sion and tightness.

Inspect hull and jet pump water intake
grate for damage. Replace or have
damaged parts repaired.

Cleaning

The bilge should be cleaned by your
dealer to remove any fuel/oil/electrolyte
deposits and mildew.

Occasionally, wash the body with wa-
ter and soap (only use mild detergent).
Remove any marine organisms from
engine and/or hull. Apply non-abrasive
wax such as silicone wax.

CAUTION:

Never clean fiberglass

and plastic parts with strong deter-
gent, degreasing agent, paint thin-
ner, acetone, etc.

Stains may be removed from seats
and fiberglass with Knight’s Spray-
Nine from Korkay System Ltd or the
equivalent.

Respect the environment by ensuring
fuel, oil or cleaning solutions do not
drain into the waterways.

WARNING

If any gasoline leak and/or odor
are present, do not start the en-
gine. Have the watercraft serviced
by an authorized Sea-Doo dealer.

F06H1UY

1

smo2001-002a.book Page 68 Wednesday, June 7, 2000 3:57 PM

www.SeaDooManuals.net

«
...
68
69
70
71
72
...
»

Summary of Contents for 2001 GS 5548





































































































Reviews:

No comments

Related manuals for 2001 GS 5548

Brand: Topper Pages: 12

42 Side Console

Brand: YAMARIN Pages: 38

CORSIVA 500 TENDER

Brand: Corsiva Yachting Pages: 38

Brand: buster Pages: 203

Activ 755 Sundeck

Brand: Quicksilver Pages: 60

MilPro Futura Commando FC 420

Brand: Zodiac Pages: 35

XLT1200 WaveRunner 2002

Brand: Yamaha Pages: 142

Brand: Sea-doo Pages: 68

Brand: Creek Company Pages: 4

ODC SUPERSPORT XR 1

Brand: Creek Company Pages: 4

WaveRunner SuperJet 2015

Brand: Yamaha Pages: 78

200 SPORT S3 2021

Brand: Saxdor Pages: 43

Brand: Point 65 Pages: 5

Brand: Boston Whaler Pages: 113

Brand: Boston Whaler Pages: 103

Brand: Boston Whaler Pages: 95

Brand: Boston Whaler Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands