manualshive.com logo in svg

Sea-doo 2001 GS 5548, Operator'S Manual, Page: 5 / 100

Share
Download
Sea-doo 2001 GS 5548 Operator'S Manual Download Page 5

3

28) Mooring Cleats .................................................................................

34

29) Footboard..........................................................................................

34

30) Boarding Pads ...................................................................................

34

31) Boarding Platform .............................................................................

34

32) Boarding Step (if so equipped)..........................................................

35

33) Cooling System Bleed Outlet ...........................................................

35

34) Flushing Connector (if so equipped) .................................................

36

35) Bilge Drain Plugs...............................................................................

36

36) Jet Pump Nozzle ...............................................................................

36

37) Reverse Gate (if so equipped) ..........................................................

36

38) Jet Pump Water Intake .....................................................................

36

FUEL AND LUBRICATION ...........................................................

37

Fueling Procedure ...................................................................................

37

Recommended Fuel ................................................................................

37

Recommended Oil ..................................................................................

38

Oil Injection System ................................................................................

38

BREAK-IN PERIOD ......................................................................

39

Engine .....................................................................................................

39

10-Hour Inspection ..................................................................................

39

DAILY PRE-OPERATION CHECKS ...............................................

40

Hull ..........................................................................................................

41

Jet Pump Water Intake ...........................................................................

41

Bilge ........................................................................................................

41

Battery.....................................................................................................

41

Fuel Tank and Oil Reservoir .......................................................................

41

Engine Compartment ..............................................................................

41

Steering System......................................................................................

41

Throttle System.......................................................................................

41

Shifter System (if so equipped) ...............................................................

42

VTS (Variable Trim System) (if so equipped)............................................

42

Safety Lanyard and Engine Start/Stop Button .........................................

42

Storage Compartment Covers.................................................................

42

OPERATING INSTRUCTIONS ......................................................

43

Principle of Operation..............................................................................

43

Boarding the Watercraft ..........................................................................

46

Starting the Engine..................................................................................

48

Rough Water or Poor Visibility Operation................................................

49

Crossing Waves ......................................................................................

49

Stopping/Docking ....................................................................................

50

Beaching..................................................................................................

50

Shutting Off the Engine...........................................................................

50

POST-OPERATION CARE.............................................................

51

General Care............................................................................................

51

Additional Care for Foul Water or Salt Water ..........................................

51

Cooling System Flushing and Engine Internal Lubrication ......................

51

Anticorrosion Treatment..........................................................................

54

smo2001-002a.book  Page 3  Wednesday, June 7, 2000  3:57 PM

www.SeaDooManuals.net

Summary of Contents for 2001 GS 5548





































































































Reviews:

No comments