Sea-doo 2001 GS 5548 Operator'S Manual Download

Page: 67 / 100

VTS Adjustment
(if so equipped)

Push on arrow pointing upward on VTS
button until the VTS stops. The nozzle
should be up without interfering with
the venturi.

TYPICAL

1. Push on arrow pointing upward on VTS

button

2. No interference
3. Nozzle up

Push on arrow pointing downward on
VTS button until VTS stops. The nozzle
must be down and it must not inter-
fere with the venturi.

1. Push on arrow pointing downward on VTS

button

2. No interference
3. Nozzle down

If VTS needs to be readjusted, refer to
an authorized Sea-Doo dealer.

CAUTION:

Trim ring and/or nozzle

should not interfere at any position.

Vacuum Bailer Pick-Ups

They are located each side of the drive
shaft tunnel.

Two pick-ups use a low pressure area
in the jet pump to siphon the water out
of the bilge when the engine is operat-
ing.

Inspect each pick-up screen for ob-
structions, clean as necessary.

TYPICAL

1. Vacuum bailer pick-ups

Water Tank Trap Drains

GTS Models

Open storage cover and check for pos-
sible obstructions at drain outlets.

1. Outlets

F01J5CY

F01J5BY

F01L7RY

F02L3KY

smo2001-002a.book Page 65 Wednesday, June 7, 2000 3:57 PM

www.SeaDooManuals.net

Summary of Contents for 2001 GS 5548





































































































Search results

Summary of Contents for 2001 GS 5548

Reviews:

Related manuals for 2001 GS 5548

Brands by name

Popular brands

Sea-doo 2001 GS 5548, Operator'S Manual

Search results

Summary of Contents for 2001 GS 5548

Reviews:

Related manuals for 2001 GS 5548

Brands by name

Popular brands