manualshive.com logo in svg

SCHUNK HGN 100, Assembly And Operating Manual

Share
Download
SCHUNK HGN 100 Assembly And Operating Manual Download Page 25

 

Maintenance and Care 

  

 

 

01.00|HGN |en 

25 

 

 

Disassembly of the module  

 

Version without gripping force maintenance 

Position of the position numbers 

(

 10, Page 31)

 

  

 

 

WARNING 

Risk of injury when the machine/system moves unexpectedly! 

Remove the energy supplies. 
Make sure that no residual energy remains in the system. 

  

1  Remove all oil feedings. 
2  Remove the cover sheet plate (5). 
3  Mark the installation position of the base jaws (2) and the  

piston (3) inside the housing (1). 

4  Turn the socket head cap screws (11) out and remove the  

cover (4). 

5  Remove the socket head cap screws (10) and remove the  

cylinder piston (6). 

6  Draw out the base jaws of the guidances and press out the piston. 

The seals (14 and 15) have to be assembled on mounting devices 

(

 9.6, Page 29)

. 

 

Maintencance of module with gripping force maintenance "O.D. 
gripping" (O.D.)  

Position of the position numbers 

(

 10, Page 31)

 

  

 

 

WARNING 

Risk of injury when the machine/system moves unexpectedly! 

Remove the energy supplies. 
Make sure that no residual energy remains in the system. 

 

9.4 

9.4.1 

9.4.2 

Summary of Contents for HGN 100





































Reviews:

No comments

Brands by name

Popular brands

Load more brands