manualshive.com logo in svg

SCHUNK HGN 100, Assembly And Operating Manual

Share
Download
SCHUNK HGN 100 Assembly And Operating Manual Download Page 17

 

Assembly 

  

 

 

01.00|HGN |en 

17 

 

 

Sensors 

The module is prepared for a number of sensors. Other sensors 
can be used with a mounting kit. 
  •  If you require further information on sensor operation, contact 

your SCHUNK contact person or download information from 
our homepage. 

  •  Technical data for the sensors can be found in the data sheets 

(included in the scope of delivery). 

 

Inductive proximity switch IN 80 

 

Fig. 4 

  

 

Fig. 5 

 Output: drawn in non-actuated condition 

 
The inductive proximity switches used are equipped with reverse 
polarity protection and are short-circuit-proof. 
Make sure that you handle the proximity switches properly: 
  •  Do not pull on the cable. 
  •  Do not allow the sensor to dangle from the cable. 
  •  Do not overtighten the mounting screw or mounting clip. 
  •  Please adhere to a permitted bend radius of the cable. (

☞

 catalog)  

  •  Avoid contact of the proximity switches with hard objects and 

with chemicals, in particular nitric acid, chromic acid and sul-
phuric acid. 

 

7.3 

7.3.1 

Summary of Contents for HGN 100





































Reviews:

No comments

Brands by name

Popular brands

Load more brands