manualshive.com logo in svg

SCHUNK HGN 100, Assembly And Operating Manual

Share
Download
SCHUNK HGN 100 Assembly And Operating Manual Download Page 10

Basic safety notes  

 

  

 

10 

01.00|HGN |en 

 

 

  

 

 

WARNING 

Risk of injury due to squeezing and bumping during movement of 
the gripper jaws and breaking or loosening of the gripper fingers! 

  

  

 

 

WARNING 

Risk of injury from objects falling and being ejected 

•   The danger zone must be surrounded by a safety fence during 

operation. 

  

  

 

 

WARNING 

While disassembling uncontrollable moves of parts of the grip-
per possible! 

   

Variant gripping force maintenance  

  

 

 

WARNING 

Risk of injury from objects falling during energy supply failure 

Products with a mechanical gripping force maintenance can, dur-
ing energy supply failure, still move independently in the direc-
tion specified by the mechanical gripping force maintenance. 

•  Secure the end positions of the product with SCHUNK SDV-P 

pressure maintenance valves. 

  

  

 

 

WARNING 

Risk of injury due to residual energy in the gripper because of 
gripping force maintenance by springs!  

  

2.7.1 

Summary of Contents for HGN 100





































Reviews:

No comments

Brands by name

Popular brands

Load more brands