manualshive.com logo in svg

Schneeberger MONORAIL, Assembly Instructions Manual, Page: 15 / 24

Share
Download
Schneeberger MONORAIL Assembly Instructions Manual Download Page 15

15

Notes

•

 

Thread connection on the hydraulic cylinder ¼" – 18 NPT,
max. pressure: 120

⋅

10³ hPa (= 120 bar).

•

 

To close the outermost rail bore holes, push out the hydraulic mounting tool
over the end of the rail.

Cover strip MAB/BAB

Cover strips can consist of several parts. The front edge of the first and last parts
are rounded. The cover strips are attached to the rail surface with double-sided
adhesive tape. The ideal bonding temperature is b18 

°

C and +30 

°

C.

CAUTION

Cover strips can bend during storage and transport, and can damage the wipers
on the carriage.

Ä

 

Support the cover strips over the entire length.

Ä

 

Do not use bent cover strips.

 

 

   

CAUTION

 

Risk of injury on the edges and ends of the cover strip.

Ä

 

Wear gloves.

1.

 

Run the carriage off the rail, see section 8.2.

2.

 

Clean the top of the rail with mineral spirits. Do 

not

 use nitro.

3.

 

Install the cover strip evenly. When doing so, pay attention to the following:

–

 

Fit the cover strip 2.5 mm from the rail edge.

–

 

Pull off the protective film (in sections in the case of long cover strips).

 

 

 

Summary of Contents for MONORAIL

























Reviews:

No comments