Scaime eNod4-B Manual Download

Page: 8 / 78

SCAIME Manual : NU-eNod4B-ETH-E-236708-D.docx

2.3

eNodView Software

So as to configure

eNod4

, SCAIME provides eNodView software tool.

eNodView

is the software dedicated to eNod devices

and digital load cell configuration from a PC. This simple graphical interface allows accessing the whole functionalities of

eNod4

for a complete setting according to the application.

eNodView

features and functions:



eNod4 control from a PC



Calibration system



Modification/record of all parameters



Measure acquisition with graphical display



Numerical filters simulation



Frequential analysis FFT



Process control



Network parameter

eNodView

software is available in English and French version and can be downloaded from our web site:

http://www.scaime.com

or ordered to our sales department on a CD-ROM support.

2.4

eNodApp - Mobile Application

So as to configure

eNod4

, SCAIME provides eNodApp application through the

Google Play Store

eNodApp

is the application

dedicated to eNod devices (fitted with the Bluetooth® option) configuration from an Android device. This simple graphical
interface allows accessing most of the functionalities of

eNod4

for a quick setting according to the application.

eNodApp

features and functions:



eNod4 control from an Android device



Calibration system



Modification/record of all parameters

eNodApp

application is available in English and French version and can be downloaded from the

Google Play Store

Summary of Contents for eNod4-B















































































Search results

Summary of Contents for eNod4-B

Reviews:

Related manuals for eNod4-B

Brands by name

Popular brands

Scaime eNod4-B, Manual

Search results

Summary of Contents for eNod4-B

Reviews:

Related manuals for eNod4-B

Brands by name

Popular brands