Scaime eNod4-B Manual Download Page 74

Page: 74 / 78

SCAIME Manual : NU-eNod4B-ETH-E-236708-D.docx

12.2.3

Conveyor

Parameter

Possible Value

Description

Conveyor Parameters



Page 1/2

Conveyor total
Length

Defines the total length of the belt in meters.

Belt Inclination

0.00 – 35.00 deg

Defines the belt title angle in degrees.

Min Weight *

For totalization

0.00 – 655.35

eNod4 enables totalization when “minimum weight to totalize” divided by
“weight section length” is greater than the minimum load to totalize.

Weight Frame *

Length

0 – 65535 mm

Represents the effective belt weigh frame length expressed in millimeters.

The effective weight section length corresponds with half of the distance
between the belt rollers which are found before and after the roller with
the belt scale.



Page 2/2

Auto. Zero
Correction

Yes / No

Dynamic zero auto-correction activation

Conveyor Zero Band

0 - 65535

Defines limit values for dynamic zero correction function. Zero function is
cancelled when the weight is out of these limits.

Material Routine
Time

0 – 6535 sec

Defines time for materials to travel distance from shear gate to weigh
section at normal speed.

Conveyor starting
alarm duration

0 – 3500 sec

For security reason, eNod4 provides buzzer function on logical output at
belt start. The buzzer duration depends on this parameter value in second.

Number of
Revolutions

1 - 65535

Specifies the real belt revolutions to realize during speed/length
calibrations and dynamic zero procedure.

Summary of Contents for eNod4-B















































































Search results

Summary of Contents for eNod4-B

Reviews:

Related manuals for eNod4-B

Brands by name

Popular brands

Scaime eNod4-B, Manual

Search results

Summary of Contents for eNod4-B

Reviews:

Related manuals for eNod4-B

Brands by name

Popular brands