Scaime eNod4-B Manual Download

Page: 65 / 78

SCAIME Manual : NU-eNod4B-ETH-E-236708-D.docx

Legal for trade
sealing

[Yes], [No]

Once legal for trade sealing activated, it forbids the change of any
parameters that can affect the eNod4 metrological specifications. Such
parameters appear in blue and are disabled over the eNodTouch
menus.

Counter (audit trail)

This number is incremented on each legal for trade sealing switching.

Checksum

Checksum calculated over set of sealed parameters when legal for
trade sealing is being activated.

eNod program
version

Program version of eNod4 embedded software.

eNod metrological
version

Version of set of metrological functions embedded in eNod4.

eNodTouch version

Program version of eNodTouch embedded software.

Data Storage Device records consultation access.

Data Storage Device (Available depending on version)

Record ID to read

Record of the ID to be read.

Erase all records from the DSD memory. This is possible only when the
legal for trade sealing is disabled.

Summary of Contents for eNod4-B















































































Search results

Summary of Contents for eNod4-B

Reviews:

Related manuals for eNod4-B

Brands by name

Popular brands

Scaime eNod4-B, Manual

Search results

Summary of Contents for eNod4-B

Reviews:

Related manuals for eNod4-B

Brands by name

Popular brands