Sapling SAM Series Page 67 Installation Manual Download | Manualshive

Page: 67 / 72

background image

67

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Diagnostic Test #1 - Protocol Verification (All Other Clocks)

Second Hand Position

2 seconds

4 seconds

6 seconds

8 seconds

10 seconds

12 seconds

14 seconds

16 seconds

18 seconds

20 seconds

22 seconds

24 seconds

Protocal and Polarity Detected

2-Wire Digital Communication, Polarity 1

2-Wire Digital Communication, Polarity 2

3-Wire Digital Communication, Polarity 1

3-Wire Digital Communication, Polarity 2

RS485 Communication, Polarity 1

RS485 Communication, Polarity 2

59 Minute Correction, Correct Polarity

59 Minute Correction, Reverse Polarity

58 Minute Correction, Correct Polarity

58 Minute Correction, Reverse Polarity

National Time/Rauland Correction, Correct Polarity

National Time/Rauland Correction, Reverse Polarity

The purpose of Diagnostic #1 is to tell the user
which protocol the master clock is using to
communicate with the secondary clock.

Diagnostic #1 may be enabled by pressing the
diagnostic button once. If the SAM clock is
performing this diagnostic, the Diagnostic LED
will flash green once every three seconds. It will
continue to flash once every three seconds until the
diagnostic is complete. The clock will confirm that
the diagnostic is complete when the LED shines a
different color.

If the LED is shining a solid green:

The Diagnostic was completed successfully.
The second hand on the SAM clock will move
to a specific second on the dial. Each second
corresponds to a particular protocol and polarity:

Red

Green

Button

The second hand will remain on this number for 3 minutes, and then the clock will revert to displaying the
accurate time.

If the LED is flashing red:

A comprehensive test is required. Please perform Diagnostic #2

LED

«
...
65
66
67
68
69
...
»

Summary of Contents for SAM Series









































































Reviews:

No comments

Related manuals for SAM Series

Brand: Nixie Clock Pages: 20

Brand: Hama Pages: 96

Brand: ICStation Pages: 2

Brand: Trevi Pages: 20

Brand: FettleLife Pages: 35

SOUND SOOTHER SI735

Brand: Sharper Image Pages: 18

Brand: Symmetricom Pages: 47

Dream Machine ICF-C211L

Brand: Sony Pages: 5

Dream Machine ICF-C414

Brand: Sony Pages: 7

Dream Machine ICF-C273

Brand: Sony Pages: 6

Dream Machine ICF-C217

Brand: Sony Pages: 4

Brand: La Crosse Pages: 14

Brand: Clas Ohlson Pages: 5

Brand: La Crosse Technology Pages: 10

Brand: La Crosse Technology Pages: 7

Brand: La Crosse Technology Pages: 5

Brand: Radio Shack Pages: 4

Brand: Oregon Scientific Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands