manualshive.com logo in svg

Sapling SAM Series, Installation Manual

Share
Download
Sapling SAM Series Installation Manual Download Page 54

54

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063 
F. (+1) 215.322.8498
www.sapling-inc.com

Description 

Power/grounding wires and 
connector

#8x1.5 Self-tapping screw

Wall anchor

Quantity 

2

4

 (not used)

4

 (not used)

Picture

Double Mount Installation - Square Clock

PLEASE NOTE:

 A user will also have to provide a Phillips-head screwdriver, a small flat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double 

gang box, Four wall anchors (must support support 50 lbs, #8 screw size, 1.5”(3.8cm) screw length), four #8 screws for the wall anchors, any equipment 
needed to install the gang box, and any additional wiring needed to extend the signal, power, or ground cables.

Included in Wiring Kits (A-PK-SAM-1)

Included in Gang Box Kit (A-GB-MK-1)

#6-32x1 screw

#6-19x3/8 screw

4

2 

(not used)

Summary of Contents for SAM Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands