manualshive.com logo in svg

Sapling SAM Series, Installation Manual

Share
Download
Sapling SAM Series Installation Manual Download Page 69

69

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063 
F. (+1) 215.322.8498
www.sapling-inc.com

Diagnostic Test #2 - Comprehensive Test (All Other Clocks)

Hour Hand Position

12

1

2

3

4

5

6

7

8

9

10

11

Time Since Clock Last Recieved Communication

Clock received communication within the last hour.

Clock received communication between 1 and 2 hours ago.

Clock received communication between 2 and 3 hours ago.

Clock received communication between 3 and 4 hours ago.

Clock received communication between 4 and 5 hours ago.

Clock received communication between 5 and 6 hours ago.

Clock received communication between 6 and 7 hours ago.

Clock received communication between 7 and 8 hours ago.

Clock received communication between 8 and 9 hours ago.

Clock received communication between 9 and 10 hours ago.

Clock received communication between 10 and 11 hours ago.

Clock received communication more than 11 hours ago.

--May signify a manufacturer default.

The purpose of Diagnostic #2 is to test the Movement 
gearbox and electrical components of your SAM clock.

Diagnostic #2 may be enabled by pressing the 
diagnostic button twice. If the SAM clock is 
performing this diagnostic, then a green LED on the 
movement will flash twice every three seconds. It will 
continue to flash twice every three seconds until the 
diagnostic is complete. 

If the LED is lit a solid green:

The second hand will display the protocol and polarity 
that was detected. See the table on the previous page 
for details.

The minute hand will display the software version 
number.

If the LED is flashing red:

The hour hand will display how much time has passed 
since the clock last received a communication signal:

The clock hands will remain on these numbers for 3 minutes, and then the clock will revert to displaying 
the accurate time.

Red

Green

Button

LED

Summary of Contents for SAM Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands