Sapling SAM Series Installation Manual Download | Manualshive

Page: 14 / 72

background image

1 2
3 4

14

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Wall Mount Installation - Round Aluminium or Wood Clock

3) Attach the communication and power wires
from your kit to the communication and power
wires in the gang box. See the sections of this
manual labeled “3-Wire Synchronous (Sync-Wire)
Communication Wiring Information” or “2-Wire
Digital Communication Wiring Information” for
additional details, depending on your system.

1) Install the single gang box in the wall. Leave at
least 4 inches between the top of the gang box and
ceiling. Confirm that the bottom of the gang box is
level with the floor.

Ceiling

Minimum

4) Insert the release lever into the hole atop the
mounting piece latch.

2) Run power and communication wiring to the
gang box. See the sections of this manual labeled
“Wiring Information” for additional details,
depending on your system.

If you are using a 2-wire system, pull the
YELLOW and GREEN wires out of
the connector.

CHECK YOUR WIRING

The voltage between the white and black wires
should measure 105-126 volts AC in the 115
volt model, 207-253 volts AC in the 230 volt
model, or 21.5-26.5 volts AC in the 24
volt model.

If you are using the 24 volt model, make sure
that the wiring leading to the clock is from an
ISOLATED transformer.

«
...
12
13
14
15
16
...
»

Summary of Contents for SAM Series









































































Reviews:

No comments

Related manuals for SAM Series

NS-CL01 - AM/FM Dual Alarm Clock Radio

Brand: Insignia Pages: 68

Brand: Techno Line Pages: 102

Brand: AudioSonic Pages: 44

Brand: La Crosse Technology Pages: 3

Brand: Philips Pages: 7

Brand: Philips Pages: 9

Brand: Philips Pages: 12

Brand: Trevi Pages: 5

Brand: Trevi Pages: 20

Brand: Tivoli Audio Pages: 2

Brand: Tivoli Audio Pages: 14

Brand: Pure Digital Pages: 2

Brand: PURE Pages: 18

Brand: Somogyi Pages: 11

Brand: Discovery Expedition Pages: 17

GIANT-DIGITS 1088

Brand: Traceable Pages: 2

Brand: iHome Pages: 16

Brand: iHome Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands