manualshive.com logo in svg

Sapling SAM Series, Installation Manual

Share
Download
Sapling SAM Series Installation Manual Download Page 19

1

3 4

2

19

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063 
F. (+1) 215.322.8498
www.sapling-inc.com

Wall Mount Installation - Square Clock

1) Install the single gang box in the wall. Leave at 
least 4 inches between the top of the gang box and 
ceiling. Confirm that the bottom of the gang box is 
level with the floor.

Ceiling

Minimum

3) Detach the housing from the back of the clock. 
Do this by inserting a flat-blade screwdriver about 
1/8 inch into each of the slot holes until the housing 
detaches. You may hear a snapping noise as the 
latches disengage.

4) Release the mounting piece from the back of 
the housing by sliding it towards the center of the 
housing, then pulling it back and away from  
the housing.

2) Run power and communication wiring to the 
gang box. See the sections of this manual labeled 
“Wiring Information” for additional details, 
depending on your system.

If you are using a 2-wire system, pull the 
YELLOW and GREEN wires out of  
the connector.

CHECK YOUR WIRING

The voltage between the white and black wires 
should measure 105-126 volts AC in the 115 
volt model, 207-253 volts AC in the 230 volt 
model, or 21.5-26.5 volts AC in the 24  
volt model. 

If you are using the 24 volt model, make sure 
that the wiring leading to the clock is from an 
ISOLATED transformer.

Mounting 
piece

Housing

1

2

Summary of Contents for SAM Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands