Sapling SAM Series Installation Manual Download | Manualshive

Page: 66 / 72

background image

66

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Second Hand Position

2 seconds

4 seconds

6 seconds

8 seconds

10 seconds

12 seconds

14 seconds

16 seconds

18 seconds

20 seconds

22 seconds

24 seconds

Protocal and Polarity Detected

2-Wire Digital Communication, Polarity 1

2-Wire Digital Communication, Polarity 2

3-Wire Digital Communication, Polarity 1

3-Wire Digital Communication, Polarity 2

RS485 Communication, Polarity 1

RS485 Communication, Polarity 2

59 Minute Correction, Correct Polarity

59 Minute Correction, Reverse Polarity

58 Minute Correction, Correct Polarity

58 Minute Correction, Reverse Polarity

National Time/Rauland Correction, Correct Polarity

National Time/Rauland Correction, Reverse Polarity

Diagnostic Test #1 - Protocol Verification (Metal Only)

The purpose of Diagnostic #1 is to tell the user
which protocol the master clock is using to
communicate with the secondary clock.

Diagnostic #1 may be enabled by pressing the
diagnostic button for one second. If the SRM
clock is performing this diagnostic, the Diagnostic
LED will flash green once every three seconds. It will
continue to flash once every three seconds until the
diagnostic is complete. The clock will confirm that
the diagnostic is complete when the LED shines a
different color.

If the LED is shining a solid green:

The Diagnostic was completed successfully. The
second hand on the clock will move to a specific
second on the dial. Each second corresponds to a
particular protocol and polarity:

The second hand will remain on this number for 3 minutes, and then the clock will revert to displaying the
accurate time.

If the LED is flashing red:

A comprehensive test is required. Please perform Diagnostic #2

Button

LED

«
...
64
65
66
67
68
...
»

Summary of Contents for SAM Series









































































Reviews:

No comments

Related manuals for SAM Series

Brand: E-Bench Pages: 49

Brand: TFA Pages: 2

Brand: Grundig Pages: 13

POWERCLOCK IBT235W

Brand: iHome Pages: 11

Brand: Roberts Pages: 32

Brand: EBENCH Pages: 13

Brand: Bresser Pages: 56

Brand: jWIN Pages: 17

Brand: LENCO Pages: 4

Brand: LENCO Pages: 8

Brand: Gorgy Timing Pages: 57

Brand: Lenoxx Pages: 7

Brand: Lenoxx Pages: 17

Brand: Datexx Pages: 1

Brand: Casio Pages: 2

Brand: Equity Pages: 4

Brand: IKEA Pages: 36

Brand: Habitat Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands