background image

4

CAUTION

 ・ WEAR  PROPER  PROTECTIVE  CLOTHING

      Do  not  wear  a  pair  of  knitted  gloves  and  work  clothing  with  lower-sleeve  edge  

      opened.   Wearing  such  gloves  and  loose  clothing  as  well  as  long  hair  could  be  

      drawn  in  or  trapped  of  by  the  rotating  parts  of  the  polisher.

4.  APPROPRIATE  INSERTED  TOOL

     ( TOOL  INSERTED  IN  THE  HAND-HELD  POWER  TOOL  TO  PERFORM  POLISHING )

WARNING

 ・ DO  NOT  MOUNT  ANY  INSERTED  TOOLS  EXCEPT  THE  ONES  FOR  POLISHING

      This  polisher  shall  not  be  used  for  cutting.   Solid  inserted  tools  will  cause  injuries.   

      Do  not  mount  any  inserted  tools  to  this  polisher  which  are  not  intended  for  the  

      polishing  operation  such  as  grinding  wheel,  cutting-off  wheel  and  dish  wheel.

 

 ・ THE  MAXIMUM  SPEED  OF  THE  INSERTED  TOOL  SHALL  BE  HIGHER  THAN  

    THE  RATED  ROTATIONAL  SPEED

      The  maximum  speed  of  the  inserted  tool  shall  be  higher  than  the  rated  rotational  

      speed  marked  on  the  nameplate  of  the  polisher  and  described  in  SPECIFICATIONS  

      in  page  8.

 

 ・ MOUNT  A  FLEXIBLE  POLISHING  PAD  DESIGNED  FOR  THIS  POLISHER

      This  polisher  is  for  polishing  operation  fitted  with  flexible  polishing  pad  and  various  

      soft  materials  or  felt  pad  for  polishing  of  surface  like  our  DIA  CERAMICA.

CAUTION

 ・ THIS  POLISHER  SHALL  BE  USED  FOR  WET-MODE  OPERATION

      Using  dry-mode  pad  will  cause  extremely  higher  temperature  and  too  much  dust,  

      resulting  in  fire  and  respiratory  diseases  at  throat  and  lungs.

5.  OPERATOR’S KNOWLEDGE TO USE THIS POLISHER

CAUTION

 ・ DO  NOT  USE  THE  POLISHER  UNTIL  GETTING  ADEQUATE  KNOWLEDGE  FOR  

    USE

      Do  not  allow  children  or  any  other  persons  to  operate  the  polisher,  who  do  not  

      know  how  to  operate  or  cannot  operate properly. 

6.  POLISHING  AT  HIGH  WORKPLACE

CAUTION

 ・ WHEN  POLISHING  AT  HIGH  WORKPLACE,  ENSURE  NOBODY  IS  UNDERNEATH

      Dropping  a  work  piece  ( polishing  material )  or  the  polisher  itself  could  cause  

      accidents  and  injuries.   When  polishing  at  high  workplace,  the  operator  is  

      recommended  to  take  fall-down  measures  such  as  safety  belt.

Summary of Contents for PA-2
























Reviews: