background image

8

Instruction Manual for Sanuvair

®

 S300

1-888-726-8869

www.sanuvox.com

Step by Step Installation | Duct-Mounted (Bypass)

1.  Locate the two 4" x 17" pre-cut rectangular openings at the back of the 

unit (one at the top, one at the bottom).

2.  Use pliers and/or your hands to unfold the metal pieces of both 

openings and position them 90° from the back of the unit.

 

Proceed for both openings.

STEP 1

STEP 2

3.  Use one of the 17" mounting angles and secure it along the rear edge 

of the unit top by using the screws already in place. Then, secure the 

second mounting angle along the rear edge at the bottom of the unit.

6.  Once the openings are cut into the duct, be sure to remove the paper 

template if you haven’t already done so. These two openings will be 

used to receive the air inlet and outlet vents that you have made at the 

rear of the unit.

4.  Use the self-adhesive foam tape and stick it around the outline of the 

two back openings to ensure their tightness when the unit is attached 

to the pipe. You will probably need to cut the tape into pieces to form the 

two tape rectangles.

7.  Install the unit vertically on the duct, aligning the openings. Secure 

the unit in place with the self-tapping screws provided for this purpose. 

Make sure you have a power outlet nearby to plug the unit into.

 

 CAUTION:

 Your S300 unit is bulky. Make sure that there are 

always 

two people to lift and handle it to avoid any injuries.

Your new SANUVAIR

®

 S300 

is now ready to operate!

STEP 3

STEP 6

STEP 4

STEP 7

5.  Unfold the paper template and position it on the ventilation duct where 

you want to attach the unit. Tape it in place with masking tape.

 

You can identify the openings to make by using a felt pen, or directly cut 

the duct with the paper template in place.

STEP 5

Summary of Contents for S300















Reviews: