Sanosil Q-Jet CT20 Operating Manual Download Page 24

Page: 24 / 32

Operating Manual Q-Jet CT20

24/32

6.5 After disinfection

•

Wait for the necessary disinfection time as well as the
minimum decay time for the disinfectant to break
down. (See section 5: usage profile)

•

Do not enter the room during the decay time

•

If you selected usage profile C: after the end of the
spray cycle, switch on the supply air and extract air
ventilation at the highest level after the minimum de-
cay time of 120 minutes in order to expel any resid-
ual H

ATTENTION

Health risk

If someone must re-enter the room before the treatment process is completed or if an H

meas-

urement must be taken, personal equipment (PES), including a full-face respirator (filter class ABEK
P3) and gloves must be worn.

•

As soon as the level of nebulised hydrogen perox-
ide in the air has decreased below 1 ppm, the
room can be used again without any restrictions

Summary of Contents for Q-Jet CT20

































Search results

Summary of Contents for Q-Jet CT20

Reviews:

Related manuals for Q-Jet CT20

Brands by name

Popular brands

Sanosil Q-Jet CT20, Operating Manual

Search results

Summary of Contents for Q-Jet CT20

Reviews:

Related manuals for Q-Jet CT20

Brands by name

Popular brands