Samsung ND-L6013R User Manual Download Page 53

Page: 53 / 170

English

_53

●

aLL

ation & connection

Connect the MIC port of the camera with the microphone or LINE OUT port of the

amplifier that the microphone is connected to.

As a microphone is built in, you can use the built-in microphone instead of an external one.

(It is applicable only to the SND-L6013/SND-L6013R/SND-L6083R model.)

Check the specifications for audio input.

•

audio codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726

ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz)

•

audio in

: Mono signal line input (Max.2.4 Vpp)

•

Line out impedance

: 600Ω

ACT LINK

NETWORK

RESET

Network

Speaker

Microphone

Amp Microphone

<SNV-L6083R>

Summary of Contents for ND-L6013R











































































































































































Search results

Summary of Contents for ND-L6013R

Reviews:

Related manuals for ND-L6013R

Brands by name

Popular brands

Samsung ND-L6013R, User Manual

Search results

Summary of Contents for ND-L6013R

Reviews:

Related manuals for ND-L6013R

Brands by name

Popular brands