Samsung DX-408 Installation Manual Download Page 51

Page: 51 / 58

3-7

MMC 804

In order to program the DX408i system by PC it is necessary to set the Service Type of the SIO
port as PCMMC using system programming (MMC 804).

Parameters related to PCMMC and remote programming are also set in system programming
(MMC 804).

The pin connections from SIO port to PC/modem are as follows.

PCMMC

SIO port

9PIN

25PIN

9PIN

RXD(2)

---------------------------------------

TXD(3)

---------------------------------------

RXD(2)

GND(5)

---------------------------------------

GND(7)

GND(5)

Remote Programming

SIO port

MODEM

9PIN

25PIN

RXD(2)

---------------------------------------

TXD(3)

---------------------------------------

RXD(2)

GND(5)

---------------------------------------

GND(7)

DTR(4)

---------------------------------------

DTR(20)

Summary of Contents for DX-408



























































Search results

Summary of Contents for DX-408

Reviews:

Related manuals for DX-408

Brands by name

Popular brands

Samsung DX-408, Installation Manual

Search results

Summary of Contents for DX-408

Reviews:

Related manuals for DX-408

Brands by name

Popular brands