Samsung DX-408 Installation Manual Download Page 20 | Manualshive

Page: 20 / 58

background image

2-4

Chapter 2

DX-408/DX-408i Digital Key System Installation

Installing System

1. Inside view of the System

Opening System Cover

The DX-408/DX-408i digital key system has two covers.

1. Opening the Side Cover

Viewed from the top, the small cover on the right side is the side cover. A round groove is
provided at the centre of the side cover marked with letters [PUSH]. To remove the cover,
pull the side cover to the right whilst gently pushing the groove.

2. Opening the Front Cover

After removing the side cover, loosen the screws at the upper and lower right portions of
the front cover. After removing the screws, hold the upper and lower sides of the front
cover and gently pull it upwards.

Front cover

Side cover

«
...
18
19
20
21
22
...
»

Summary of Contents for DX-408



























































Reviews:

No comments

Related manuals for DX-408

Brand: Selta Pages: 102

Brand: MagicBox Pages: 44

Brand: Gigaset Pages: 28

Brand: AGFEO Pages: 84

Touch Screen Caller ID Phone

Brand: ENZER Pages: 5

Brand: VTech Pages: 7

Brand: Telematrix Pages: 22

Brand: Kodak Pages: 25

Brand: Angekis Pages: 2

Brand: ALcom Pages: 14

Brand: D-Link Pages: 38

Brand: D-Link Pages: 67

Brand: Daewoo Pages: 30

Brand: Daewoo Pages: 102

Brand: Topcom Pages: 24

Brand: Topcom Pages: 16

Brand: CEECO Pages: 11

Brand: CEECO Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands