Samsung DX-408 Installation Manual Download Page 38 | Manualshive

Page: 38 / 58

background image

2-22

Chapter 2

DX-408/DX-408i Digital Key System Installation

Direction mark

EVEN 2

EVEN 1

ODD 2

ODD 1

Direction mark

EVEN 2

EVEN 1

ODD 2

ODD 1

5. Install the new EPROMs with caution in the designated locations (ODD1 and EVEN1 for

DX-408, ODD1, ODD2, EVEN1 and EVEN2 for DX-408i) according to the diagram.
Ensure the orientation notches on the EPROMs line up with the notches on the EPROM
sockets.

6. Turn the MEM switch to the off position for 10 seconds then to the ON position

7. Turn on the power at the GPO and the system.

8. In the case where an external battery was installed, re-connect the cable for battery

connection.

9. Close the front and side covers of the DX-408/DX-408i system.

10. Initialise the system as per a new installation – MMC 812 (Set Country Code) etc

11. Reprogram the system using PCMMC or manually.

DCS-408

DCS-408i

«
...
36
37
38
39
40
...
»

Summary of Contents for DX-408



























































Reviews:

No comments

Related manuals for DX-408

Brand: Samsung Pages: 6

Brand: 3Com Pages: 3

Brand: 3Com Pages: 2

Brand: NEC Pages: 7

Brand: NEC Pages: 2

Brand: NEC Pages: 3

Brand: Telstra Pages: 6

Brand: AT&T Pages: 124

Touch Tone Capture

Brand: Chase Pages: 10

Brand: VTech Pages: 46

Brand: Q-Light Pages: 2

Brand: Panasonic Pages: 64

Brand: Yealink Pages: 24

Brand: Kraun Pages: 2

Brand: GE Pages: 38

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands