Samsung DX-408 Installation Manual Download Page 50 | Manualshive

Page: 50 / 58

background image

3-6

Chapter 3

Additional Equipment Connection

PC and Remote Programming

This feature is applicable to the DX-408i digital key system only.

To program the system via a personal computer (PC) or customer-provided modem (remote
programming), connect a modem or a PC to the SIO serial port of the DX-408i digital key
system using an RS-232C cable. The PC must be equipped with the Samsung proprietary
program, PCMMC.

When the PC or modem needs to be more than 5 metres away from the DX-408i
digital key system, shielded computer cable is required. The cable must not
exceed 15 metres.

SIO port

«
...
48
49
50
51
52
...
»

Summary of Contents for DX-408



























































Reviews:

No comments

Related manuals for DX-408

Brand: NEC Pages: 4

Brand: Panasonic Pages: 252

Brand: Panasonic Pages: 8

Brand: Radio Shack Pages: 20

Brand: Audiovox Pages: 40

Brand: Sagem Pages: 2

Brand: Uniden Pages: 47

Sailor System 5000 MF/HF

Brand: Sailor Pages: 56

MARQUIS 9600 Series

Brand: Telematrix Pages: 30

Brand: AUDIOLINE Pages: 40

Brand: Shiro Pages: 23

Brand: BT Pages: 82

Unity OpenStage M3 Ex

Brand: Atos Pages: 104

Brand: GE Pages: 2

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: SpectraLink Pages: 79

Brand: Snom Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands