Samsung DVD-709, Service Manual

Page: 18 / 179

Reference Information
Samsung Electronics 2-11
N A M E
M P 7
M P 6
M P 5
M P 4
M P 3
M P 2
M P 1
M P 0
V
D D 2
V
S S 2
R T C I
VDD
1 2 C
S A
V
S S A 1
R ( C r )
C
V
D D A 1
G ( Y )
VBS
V
D D A 2
B ( C b )
CVBS
V
D D A 3
V
S S A 2
V
S S A 3
X T A L
X T A L 1
I / O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
O
O
I
O
O
I
O
O
I
I
I
O
I
PIN
9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2 0
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
3 0
3 1
3 2
3 3
3 4
3 5
FUNCTION
Digital supply voltage 2
Digital ground 2
Real Time Control input. If the LLC1 clock is provided by an SAA7111 or SAA7151B, RTCI should be
connected to the RTCO pin of the respective decoder to improve the signal quality.
Sense input for 12C bus voltage;connect to 12C bus supply
Select 12C address; low selects slave address 88h, high selects slave address 8Ch.
Analog ground 1 for Red (Cr), C(CVBS), Green(Y) outputs
Analog ground 3 for the DAC reference ladder and the oscillator
Crystal oscillator output
Crystal oscillator input; if the oscillator is not used, this pin should be connected to ground.
Analog output of Red (Cr)signal
Analog output of Chrominance (CVBS) signal
Analog supply voltage 1 for R(Cr), C(CVBS) outputs
Analog output of Green(Y) signal
Analog output of VBS (CVBS) signal
Analog supply voltage 2 for VBS(CVBS), Green(Y) outputs
Analog output of Blue(Cb) signal
Analog output of CVBS(CSYNC) signal
Analog supply voltage 3 for Blue(Cb)and CVBS(CSYNC), outputs
Analog ground 2 for VBS (CVBS), Blue(Cb), CVBS(CSYNC)outputs
Double speed 54 MHzMPEG port. It is an input for "CCIR 656" style multiplexed Cb, Y, Cr data.
Data are sampled on the rising and falling clock edge;data sampled on the risting edge then are sent to
the encoding part of the device, data sampled on the falling edge are sent to the RGB part of the device.
(or vice verse, depending on programming)
V
D D A 4
XCLK
V
S S 3
V
D D 3
RESN
S C L
S D A
TTXRQ
T T X
I
O
I
I
I
I
I / O
O
I
3 6
3 7
3 8
3 9
4 0
4 1
4 2
4 3
4 4
Analog supply voltage 4 for the DAC reference ladder and the oscillator
Clock output of the crystal oscillator
Digital supply ground 3
Digital supply 3
12C serial clock input
12C serial data input/output
Teletext Request output, indicating when text bits are requested
Teletext bit stream input
Reset input, active LOW. After reset is applied, all digital I/Os are in input mode; PAL-
Blackburst on CVBS, VBS and C;RGB outputs set to lowest voltage.
The 12C-bus receiver waits for the START condition.