Samsung CLX-FIN40L Service Manual Download

Page: 37 / 148

2. System Configuration

2-15

SAMSUNG ELECTRONICS

Service Manual
CLX-FIN40S/CLX-FIN40L

2.5 Block diagram

2.5.1 Construction diagram of boards

This system consists of the following boards.

2.5.2 Function of each board

•

FINISHER MAIN board

This is the board to mainly control the finisher module and consists of the micro-controller and driver ICs.

•

BRIDGE DRIVE board

This is the board to drive the bridge module and controlled by the FINISHER MAIN board.

•

MANUAL STAPLE board

This is the board to display manual stapling condition and accept button input to do manual staple operation.

•

BOOKLET MAKER board

This is the board to control the booklet maker module and consists of the micro-controller and driver ICs.

•

HOLE PUNCH board

This is the board to control the hole punch module and consists of the micro-controller and driver ICs.

FINISHER MAIN

ENGINE

MANUAL STAPLE

BRIDGE DRIVE

BOOKLET MAKER

HOLE PUNCH

(OPTION)

Summary of Contents for CLX-FIN40L





















































































































































Search results

Summary of Contents for CLX-FIN40L

Reviews:

Related manuals for CLX-FIN40L

Brands by name

Popular brands

Samsung CLX-FIN40L, Service Manual

Search results

Summary of Contents for CLX-FIN40L

Reviews:

Related manuals for CLX-FIN40L

Brands by name

Popular brands