Samsung CLX-FIN40L Service Manual Download

Page: 142 / 148

4. Troubleshooting

4-37

SAMSUNG ELECTRONICS

Service Manual
CLX-FIN40S/CLX-FIN40L

4.3 Finisher Self-Test Mode

The finisher has the Self-Test mode. In this mode, you can operate the finisher without paper. Although

there is no paper, the finisher works at the same way.

4.3.1 How to use the Self-Test mode

To use the Self-Test mode, follow the below procedure.

1. Turn the machine off.

2. Set the finisher DIP switch.

3. Turn the machine on.

4. The finisher initializes and works in Self-Test mode.

Caution

Remove the staple cartridge before entering the Self-Test mode. The staples can go inside the machine.

Remove the staple cartridge before entering

the Self-Test mode.

Remove the staple cartridge before entering

the Self-Test mode.

Summary of Contents for CLX-FIN40L





















































































































































Search results

Summary of Contents for CLX-FIN40L

Reviews:

Related manuals for CLX-FIN40L

Brands by name

Popular brands

Samsung CLX-FIN40L, Service Manual

Search results

Summary of Contents for CLX-FIN40L

Reviews:

Related manuals for CLX-FIN40L

Brands by name

Popular brands