background image

13

English

Unit instal

lation

Outdoor unit drain work

General area

While the air to water heat pump is operating in heating mode, ice 

can accumulate on the surface of the condenser.
To prevent ice from growing, the system occasionally enters a 

defrost mode and the ice on the surface thaws off.
Water dripping from the condenser is guided through the drain 

holes to prevent ice formation inside the base plate at subzero 

temperatures.

•  In case there is not enough space for natural drainage from the 

outdoor unit, additional drain work is required. 

Follow the description as per below:

 

– Provide a minimum of 150 mm of free space to the floor.

 

– Insert the drain plug into the hole at the bottom of the 

outdoor unit.

 

– Connect the drain hose to the drain plug.

 

– Make sure dirt and debris cannot block the drain (hose). 

Clean the base plate whenever needed.

 

– For the remaining holes (that do not have the drain plug), 

insert the drain cap

 

– Make sure that the water dripping from the drain hose runs 

away correctly and safely.

≥ 150 mm

  WARNING

•  If the drainage is not adequate, it can lead to stagnant water 

and ice build-up, causing system performance issues and 

possible damages.

Drain hole Φ 20

Drain plug x 1ea

212.5 mm

13 mm

Prepare a water drainage channel around the foundation, to 

drain waste water from around the unit.

If the water drainage from the unit is inadequate, please raise 

the unit on construction concrete blocks, etc. (the height of the 

construction should be at least 150 mm).

If you install the unit on a frame, please install a slanted 

waterproof plate within 150 mm of the underside of the unit 

to prevent water from plashing against the bottom plate from 

below.

When installing the unit in a place frequently exposed to snow, 

pay special attention to elevating the foundation as high as the 

average snow height plus the additional required 150 mm.

If you install the unit on a wall support bracket, please install 

drainage pipework. In order to avoid the drain water from 

dripping on the floor potentially creating a slippery surface or 

an ice layer under freezing conditions.

※ 

Please securely mount the outdoor unit before connecting the 

water piping.

Summary of Contents for AE CXYD Series































Reviews: