Samsung 400UX - SyncMaster - 40" LCD Flat Panel Display User Manual Download

Page: 19 / 149

DUAL-

STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM

MONO/NICAM STEREO can be operated depending on the

broadcasting type by using the DUAL button on the remote

control while watching TV.

- This is activated when a TV tuner box is installed.

ENTER/PRE-CH

This button is used to return to the immediately previous

channel.

- This is activated when a TV tuner box is installed.

MUTE

Pauses (mutes) the audio output temporarily. This is dis-

played on the lower left corner of the screen. The audio

comes back on if MUTE or - VOL + is pressed in the Mute

mode.

CH/P

mode, selects TV channels.

- This is activated when a TV tuner box is installed.

Selects the

mode directly.

- This is activated when a TV tuner box is installed.

Opens the on-screen menu and exits from the menu or

closes the adjustment menu.

RETURN

Returns to the previous menu.

EXIT

Exits from the menu screen.

MagicInfo

MagicInfo

Quick Launch Button.

Note

This button is disabled for products that do not support

MagicInfo

User Installation Guide

Note

• Be sure to call an installation expert of Samsung Electronics to install the product.

• The warranty becomes invalid if the product is installed by someone other than a profes-

sional authorized by Samsung Electronics.

• A Samsung Electronics service center can provide details.

Tilt Angle and Rotation

Introduction

Summary of Contents for 400UX - SyncMaster - 40" LCD Flat Panel Display






















































































































































Search results

Summary of Contents for 400UX - SyncMaster - 40" LCD Flat Panel Display

Reviews:

Related manuals for 400UX - SyncMaster - 40" LCD Flat Panel Display

Brands by name

Popular brands

Samsung 400UX - SyncMaster - 40" LCD Flat Panel Display, User Manual

Search results

Summary of Contents for 400UX - SyncMaster - 40" LCD Flat Panel Display

Reviews:

Related manuals for 400UX - SyncMaster - 40" LCD Flat Panel Display

Brands by name

Popular brands