Samsung 400UX - SyncMaster - 40" LCD Flat Panel Display Page 17 User Manual Download

Page: 17 / 149

• These are general instructions. For exact

instructions, see the User Manual sup-

plied with the locking device.

• You can purchase the locking device

from an electronics store, an online shop,

or our service center.

Note

See the "Connections" section for details about cable connections.

Remote Control

Note

The performance of the remote control may be affected by a TV or other electronic device

operating near the LCD Display , causing a malfunction due to interference with the frequen-

cy.

A TV tuner box (sold separately) must be connected to use the TV. (US Only)

POWER
OFF

Number Buttons

/ GUIDE button

+ VOL -

SOURCE

D.MENU

TOOLS

Up-Down Left-Right buttons

INFO

The Color button and the PC/DVI/HDMI/DP

selection button

TTX/MIX

MTS/DUAL

ENTER/PRE-CH

MUTE

CH/P

TV
MENU

RETURN

EXIT

MagicInfo

POWER

Turns the product On/Off.

Introduction

Summary of Contents for 400UX - SyncMaster - 40" LCD Flat Panel Display






















































































































































Search results

Summary of Contents for 400UX - SyncMaster - 40" LCD Flat Panel Display

Reviews:

Related manuals for 400UX - SyncMaster - 40" LCD Flat Panel Display

Brands by name

Popular brands

Samsung 400UX - SyncMaster - 40" LCD Flat Panel Display, User Manual

Search results

Summary of Contents for 400UX - SyncMaster - 40" LCD Flat Panel Display

Reviews:

Related manuals for 400UX - SyncMaster - 40" LCD Flat Panel Display

Brands by name

Popular brands