Sam sam-12 Directions For Use Manual Download Page 14 | Manualshive

Page: 14 / 35

background image

15

ZetrOZ, Inc.

Product Support

203-349-2798

10.3.2. DUAL-APPLICATOR MODE

The Y-adapter (optional) may be used to power two Applicators simultaneously. As
shown in Figure 8, connect the Y-adapter directly to the Power Controller wire and then
connect each Applicator to a wire jack at the other end of the Y-adapter.

When using two

sam

Applicators and two

sam

Ultrasound Coupling Bandages

simultaneously, the

sam

Ultrasound Coupling Bandages should be positioned so that

their footprints do not overlap.

Caution: DO NOT overlap

sam

Ultrasound Coupling Bandages (Figure 6).

Caution: DO NOT use the Y-adapter when using only one applicator for treatment.

Caution: Do NOT attach more than one Y-adapter to the

sam

Device.

Note: If two applicators will be used, two

sam

Ultrasound Coupling Bandages (one for

each applicator) and the Y-adapter must be used for the treatment.

ﬁ gure 6: NO Bandage Overlap

«
...
12
13
14
15
16
...
»

Summary of Contents for sam-12




































Reviews:

No comments

Related manuals for sam-12

Brand: MAHLE Pages: 21

Brand: Latchways Pages: 80

Brand: Kapriol Pages: 28

Brand: Xebex Fitness Pages: 15

Brand: qeedo Pages: 2

Brand: Garmin Pages: 10

Brand: Naviom Pages: 31

Brand: R&S Pages: 371

Brand: R.M. Young Pages: 9

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brand: Raymarine Pages: 15

Brand: RaycoWylie Pages: 9

Brand: Raven Pages: 58

Brand: Raven Pages: 26

Brand: Ravo Pages: 114

Brand: Alcoscan Pages: 6

Brand: Vatech Pages: 137

Brand: Vatech Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands