SAF Lumina Series Configuration Manual Download Page 25

Page: 25 / 123

2.4

Resetting the CFIP Lumina

Depending on the method used, the user may reset the whole terminal or the management

controller individually, see table below for details.

Reset action unplugging power source.

Restarts both the multiplexer module and the management

module. Resets all management counters.

Resetting with

button in

Web GUI ‘Configuration



System

configuration’ window or using command

prompt command “

system reset

”

Restarts CPU of the management controller. Resets all

management counters.

Resetting with command prompt command

“

system reset cold

”

Restarts modem and CPU of the management controller. Resets

all management counters.

2.5

Web Interface

This section describes operation of Web interface.

2.5.1

ODC Port

ODC port is used to connect the CFIP Lumina to a PC or Ethernet network for Web, SNMP and

Telnet management.

(!)

The length of single mode FO cable can be up to 10 kilometres (6.2 miles).

2.5.2

Ethernet Management Connection Configuration

Before you proceed to initial link setup with Web GUI, you must perform Ethernet connection

configuration by following these steps:

In “MS Windows” operational system go to Start



Settings



Network connections (or

Start



Settings



Control panel



Network connections)

The CFIP Lumina Series Full Outdoor Unit Technical Description and Configuration Guide • Rev. 1.10 •

© SAF Tehnika JSC 2013

Summary of Contents for Lumina Series




























































































































Search results

Summary of Contents for Lumina Series

Reviews:

Related manuals for Lumina Series

Brands by name

Popular brands

SAF Lumina Series, Configuration Manual

Search results

Summary of Contents for Lumina Series

Reviews:

Related manuals for Lumina Series

Brands by name

Popular brands