SAF Lumina Series Configuration Manual Download Page 105

Page: 105 / 123

Software Update

To simplify the firmware update process, SAF Tehnika JSC provides special update package, as a

new version is available. This update pack is available as archive (e.g. zip), which includes firmware file

(with *.elf.ezip,Ec extension), upgrade instructions, release notes and MIB files for SNMP protocol.

The latest CFIP series firmwares are available in the following URL:

https://www.saftehnika.com/downloads/firmware/cfip

(registration required)

The main method for firmware upgrade is being done via Web GUI, which automates the whole

firmware upgrade process. To perform software upgrade from Web GUI, please go to “Configuration



System configuration” and in “Upgrade software” section press “Browse…” button and locate

firmware upgrade file (e.g. cfipf000.elf.ezip,Ec) on your hard disk.

Although upgrade procedure usually takes less than 1 min.,

Management CPU might initiate

defragmentation of flash memory and upgrade process may take up to 3-5 minutes. Please do not

unplug power until firmware upgrade procedure is finished - Web GUI will automatically reconnect

and login page will appear.

Besides there are other various ways how the user can update the CFIP management software by

uploading the appropriate firmware file to the CFIP Lumina flash disk and further editing boot

configuration file if necessary. The file upload can be performed:

–

via Ethernet management port using update package,

–

via Ethernet management port using FTP,

–

via Ethernet management port using TFTP, or
via RS232 serial port using Xmodem protocol.

Following chapters

describe other methods how to update software.

8.1

Update Software with Update Pack

To update CFIP software using the update pack, proceed as follows:

–

uncompress the package;

–

change the CFIP IP address to 192.168.205.10,

edit ‘send.205.xx’ files by replacing

“192.168.205.10” with actual CFIP IP address;

–

arp –d

ip_addr

[

if_addr

] deletes the host specified by ip_addr. If another host with a

duplicate IP address exists on the network, the ARP cache may have had the MAC address

for the other computer placed in it.

arp –d

is used to delete an entry that may be

incorrect. By default no host is specified.

–

rem

ttftp.exe 192.168.205.10 put help.txt

prefix ignores command execution

The CFIP Lumina Series Full Outdoor Unit Technical Description and Configuration Guide • Rev. 1.10 •

© SAF Tehnika JSC 2013

Summary of Contents for Lumina Series




























































































































Search results

Summary of Contents for Lumina Series

Reviews:

Related manuals for Lumina Series

Brands by name

Popular brands

SAF Lumina Series, Configuration Manual

Search results

Summary of Contents for Lumina Series

Reviews:

Related manuals for Lumina Series

Brands by name

Popular brands