![background image](http://html1.mh-extra.com/html/sabo/43-accu/43-accu_operators-manual_3195804045.webp)
11
Excessive grass waste in
the housing or ejection
channel.
Clear the cutting
chamber/ejection channel of
grass, keep the gap between
fan and housing clean (remove
the safety key first
K2
).
Mower does not work
Pull drive control bar not
pulled.
Pull drive control bar
G
.
Standby mode not on.
Before moving the drive
safety control bar, switch on
standby mode (9)
H
.
Have it checked by an
authorised workshop.
Mower cannot be
moved backwards
Centrifugal clutch of the
drive still engaged.
Push mower forwards
minimally without the on to
release the clutch.
Speed cannot be
regulated
Standby mode not on.
Before activating the speed
adjustment, switch on
standby mode (9)
H
.
Have it checked by an
authorised workshop.
Extreme vibration
Have it checked by an
authorized dealer
Cut not clean, lawn
turns yellow
Cutting blade blunt.
Have it sharpened and
balanced by an authorised
workshop
Q
.
Cutting height too low.
Set higher cutting height
I
.
Mowing speed too high.
Adjust mowing speed.
Insufficient overlap
between mowing lanes.
If grass is long, the mowing
lanes may need to overlap
further.
Lawn matted.
A perceptible improvement
can be achieved by using a
scarifier.
Mowing in energy-saving
mode under difficult
conditions.
Switch off energy-saving
mode.
Ejector blocked
Turbo signal ignored
J
+
K
.
Empty the collecting bag
L
.
Cutting height too low
with grass too high.
Set higher cutting higher
I
.
Mowing speed too high.
Adjust mowing speed.
Grass is damp.
Allow the lawn to dry.
Mowing in energy-saving
mode under difficult
conditions.
Switch off energy-saving
mode.
The mulched grass
does not look good:
clumps, excessive cut
material, coarse cut
Cutting blade blunt.
Have it sharpened and
balanced by an authorised
workshop
.
Mulching rule ignored
(cut max. 1/3 of grass
height; the grass height
to be cut must be less
than 10 cm)
Set higher cutting height
I
.
Convert mower to rear
ejection
U2
+
S1
and mow
lawn with high cutting height
first.
Driving speed too high.
Adapt driving speed, switch
motor drive off if necessary.
Grass accumulation
under the mower blade.
Set higher cutting height
I
.
Insufficient overlap
between mowing lanes.
If grass is long, the mowing
lanes may need to overlap
further.
Grass is damp.
Set higher cutting height
I
.
Allow the lawn to dry.
In case of faults and defects which have not been listed here, please contact the
nearest authorized dealer.
Repairs which require specialized knowledge should only be performed by a qualified
expert. Your authorized dealer will naturally also be glad to help if you do not wish to
perform the maintenance work described here yourself.
21 FAULT DISPLAY (FIG.
H
(10) )
Frequency of the
flashing signal / signal
tone
Meaning
Correcting the fault
1 x
Motor does not reach the
set speed.
Restart motor.
Check the battery is
charged., charge if
necessary.
Have it checked by an
authorised workshop.
2 x
Fault with control circuit
board when starting.
Restart motor.
Have it checked by an
authorised workshop.
3 x
Communication between
battery and control circuit
board interrupted.
Check whether the battery is
fitted correctly in the battery
compartment, correct if
necessary and restart motor.
Have it checked by an
authorised workshop.
4 x
Overload on cutter motor
or drive motor.
Clean grass from cutting
area/ejector channel, remove
blockages (remove safety
key before hand
K2
!).
When mowing on a slope:
Reduce speed or switch off
drive. Mow at right-angles to
the slope, not up and down.
5 x
Battery capacity low.
Charge battery.
6 x
Motor, control circuit
board or battery
overheated.
Allow the mower to cool.
7 x
Overload on cutter motor
or drive motor.
Clean grass from cutting
area/ejector channel, remove
blockages (remove safety
key before hand
K2
!).
When mowing on a slope:
Reduce speed or switch off
drive. Mow at right-angles to
the slope, not up and down.
8 x
Control element for
starting the cutter motor
activated in the wrong
order.
Note the correct operating
sequence for starting the
cutter motor (see chapter
"Start the cutter motor"
).
9 x
Software error.
Restart motor.
Have it checked by an
authorised workshop.
22 TECHNICAL DATA
Cutter motor
Motor
40 V DC motor
Motor speed
Standard setting
2800 rpm
Energy-saving mode
2600 rpm
Automatic speed increase
under difficult mowing conditions
3000 rpm
Charger
See separate instructions for the charger.
Battery
Summary of Contents for 43-ACCU
