![background image](http://html1.mh-extra.com/html/ryobi/s630d/s630d_operators-manual_1506331008.webp)
8 - English
OPERATION
WARNING:
Do not allow familiarity with products to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
Sanding on wood surfaces
Removing rust from and sanding steel surfaces
SANDPAPER SELECTION
Selecting the correct size grit and type sandpaper is an
extremely important step in achieving a high quality sanded
finish. Aluminum oxide, silicon carbide, and other synthetic
abrasives are best for power sanding. Natural abrasives,
such as flint and garnet are too soft for economical use in
power sanding.
In general, coarse grit will remove the most material and finer
grit will produce the best finish in all sanding operations. The
condition of the surface to be sanded will determine which
grit will do the job. If the surface is rough, start with a coarse
grit and sand until the surface is uniform. Medium grit may
then be used to remove scratches left by the coarser grit and
finer grit used for finishing of the surface. Always continue
sanding with each grit until surface is uniform.
NOTE: Do not use sander without sandpaper. Doing so will
damage the cushion.
INSTALLING SANDPAPER
The cushion on the sander gives you the option of using
either non-adhesive sandpaper that clamps to the platen or
adhesive backed sandpaper with pressure sensitive adhesive
backing that sticks to the cushion.
INSTALLING NON-ADHESIVE SANDPAPER
See Figure 2, page 11.
Inspect sandpaper before installing.
Do not use if broken
or defective.
Unplug the sander.
NOTE: Removing the dust bag assembly will make installing
non-adhesive sandpaper easier.
Always remember to replace
the dust bag assembly before beginning operation.
If replacing sandpaper, remove old sandpaper. To remove
sandpaper, a lever is located on each side of the sander.
Release paper clamps securing sandpaper by lifting up
on each lever and disengaging from slot in platen.
Insert end of new 1/3 sheet sandpaper approximately
1/2 in. under the front paper clamp.
Lift up on lever on the left side of sander and lock into
slot on platen. Apply downward pressure to conform
sandpaper to platen.
Wrap sandpaper around cushion and insert loose end
of sandpaper under the rear paper clamp. Fit sandpaper
against cushion as tight as possible.
Lift up on lever on the right side of sander and lock into
slot on platen.
INSTALLING ADHESIVE SANDPAPER
See Figure 3, page 11.
Unplug the sander.
If replacing adhesive sandpaper, remove old sandpaper
by peeling it off cushion. If removing non-adhesive sand-
paper, release paper clamp by lifting up on each lever,
then remove sandpaper.
Place levers back in locked position.
NOTE: Always check to make sure levers are in locked
position before turning sander on.
Carefully peel adhesive backing from new 1/3 sheet
sandpaper.
Position sandpaper, making sure front edge of sandpaper
is aligned with front edge of the cushion. Carefully press
sticky side of sandpaper on cushion.
NOTE: Sandpaper must be aligned with the front edge
of the cushion for proper functioning of the flush sanding
feature.
NOTE: It is recommended that you clean the cushion occa-
sionally by brushing lightly with a small brush. Dust build-up
on cushion could cause sandpaper to not stick.
Summary of Contents for S630D
Page 31: ...13 notes NOTAS...