![background image](http://html1.mh-extra.com/html/ryobi/rmt18/rmt18_manual_1506304003.webp)
Safety, performance, and dependability have been given
top priority in the design of your multi tool.
INTENDED USE
The multi tool is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual and can be considered responsible for their
actions.
The multi tool is intended to be used:
–
for sanding and finishing metal, wood, plastics, or
similar materials using the sanding pad with the
shaped abrasive sheets provided
–
for scraping and plunge-cutting into non-ferrous
metal, wood, plastics, plasterboard, etc. using the
provided metallic cutting blades
–
for cutting holes in walls to accommodate switches
or power sockets
–
for removing grouting from between ceramic tiles
The multi tool is intended to be operated indoors in dry, well-
illuminated, and adequately ventilated conditions.
The multi tool is not intended to be used on wet materials
or surfaces.
Do not use the product in any way other than those stated
for intended use.
WARNING!
Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below
may result in electric shock,
fi
re and/or serious injury.
Save all warnings and instructions for future reference.
MULTI TOOL SAFETY WARNINGS
■
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
■
Always wear safety goggles and a dust mask when
sanding, especially sanding overhead.
■
A suitable breathing respirator must be worn while
sanding lead paint, some woods, and metal to avoid
breathing the harmful/toxic dust or air.
■
The dust produced when using the product may be
harmful to the health of the operator and bystanders.
Operator and bystanders shall not touch and not inhale
the dust. Wear a suitable dust protection mask.
■
Do not machine any materials that present a danger to
health, such as asbestos.
■
Clamp the workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
■
Switch the product off immediately if the accessory
stalls. Do not switch the product on again while the
accessory is stalled, as doing so could trigger a sudden
recoil with a high reactive force. Determine why the
accessory stalled and rectify this, paying heed to the
safety instructions.
■
Ambient temperature range for tool during operation is
between
0
°C and
40
°C.
■
Ambient temperature range for tool storage is between
0
°C and
40
°C.
■
The recommended ambient temperature range for the
charging system during charging is between
10
°C and
38
°C.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack, or charger in fluid or allow fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between
0
°C and
40
°C.
■
Ambient temperature range for battery storage is
between
0
°C and
20
°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 57.
1. LED light
2. Blade locking screw
3. Speed control
4. Lock on switch
5. On/off switch
6. Handle, insulated grasping surface
7. Battery port
8. Hex key
9. Plunge cut blade
10. Flush cut blade
11. Adaptor */**
12. Sandpaper
13. Sanding pad
14. Operator’s manual
15. Battery pack
16. Charger
*Compatible with BOSCH accessories. BOSCH is a
registered trademark of Robert Bosch GmbH.
**Compatible with DREMEL accessories. DREMEL is a
registered trademark of Robert Bosch Tool Corporation.
MAINTENANCE
■
The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product from the power
supply will prevent accidental starting that could cause
serious injury.
■
When servicing, use only original manufacturer’s
replacement parts, accessories and attachments. Use
of any other parts may create a hazard or cause product
damage.
■
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.
■
Do not at any time let brake fluids, gasoline, petroleum-
ENGLISH
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
3
Original Instructions
Summary of Contents for RMT18
