MAINTENANCE
Infrequent Lubrication as Required
■
Apply automotive type oil directly on slide tubes. It will
be picked up and dispersed by built in felt wicks.
■
Apply a light oil or a pressurized light spray oil to the
arm pivot shaft (47).
■
Apply a light oil or a pressurized light spray oil to the
torsion spring (46) as shown.
■
Apply a light oil or a pressurized light spray oil to the
lower guard spacer (44), roller (45) and cover plate (3)
as shown.
MOTOR BELT TENSION (FIG. 26)
The motor belt tension was properly adjusted at the
factory. However, to check the belt tension:
■
Use a Phillips screwdriver to remove the five screws
holding the belt cover and remove the cover.
■
To check the belt tension squeeze the belt. Using light
pressure the belt should deflect approximately
25.4 mm.
■
To adjust the tension:
- Use a Phillips screwdriver to loosen(but do not
remove) the six motormount screws.
- To increase the belt tension turn the adjusting
socket head set screw clockwise. To decrease the
tension turn the adjusting set screw counter-
clockwise.
Note:
Excessive belt tension will cause the motor to
fail prematurely.
- Securely tighten the six motormount screws.
■
Replace the belt cover.
28
GB
F
D
E
English
I
P
NL
S
DK
N
FIN
GR
H
CZ
RUS
RO
PL
TROUBLESHOOTING GUIDE
General
Problem
Probable Cause
Suggested Corrective Action
Blade hits table
1. Misalignment
1. Get authorized Service
Angle of cut not accurate
1. Misalignment
1. See “Alignment” section
Can’t move miter adjustment
1. Sawdust under table
1. Vacuum or blow out dust
Wear Eye Protection
Power head wobbles
1. Loose pivot points
1. See Bevel Pivot Adjustment
in “Alignment” section
Power head won’t fully rise
1. Lubrication needed
1. See “Lubrication” section
or blade guard won’t fully close
2. Part failure
2. Get authorized Service
3. Pivot spring or guard spring
3. Get authorized Service
not replaced properly after service
4. Sawdust sticking to stops
4. Inspect/clean stops
Blade binds, jams, burns wood
1. Improper operation
1. See “Basic Saw Operation” section
Rough cuts
2. Dull blade
2. Replace or sharpen blade
3. Improper blade
3. Replace with 305mm diameter blade
designed for the material being cut
4. Bent blade – check flatness
4. Replace blade
across expansion slots on blade
Tool vibrates or shakes
1. Sawblade not round
1. Replace blade
2. Sawblade damaged
2. Replace blade
3. Sawblade loose
3. Tighten arbor screw
4. Other
4. Get authorized Service
Power head hard to
1. Lube needed
1. See - “Lubrication” section
pull/push down
EMS-1830SC manual 14/05/04 12:26 Page 28
Summary of Contents for EMS-1830SC
