Ruida Technology LFS-PM Series Operating Manual Download Page 22

Page: 22 / 35

LFS-PM Series Live Focus System Operating Manual

3.1.11 HMI Interface

The connection between the distance controller and the displayer is shown as

follows:

color of wire

touch screen

read

blue

brown

yellow

3.1.12 USB Interface

USB is a U disk interface that used to upgrade the firmware.

LAN is a ETHERNET interface.

3.2

Led Indicator

LED name

Description

+24V

24V Power indicator

Run

System running indicator

Trace

Tracing signal indicator

Punch

Piercing indicator

WrkOk

Work finish indicator

UpOk

Rising up ok indicator

DnOk

Tracing down ok indicator

AlmOut

Alarm indicator

Lmt+

Up limit indicator. Low level input will turn on the led

Lmt-

Down limit indicator. Low level input will turn on the led

EmStp

Emergency stop input. Low level input will turn on the led

In1

Low level input will turn on the led

In2

Low level input will turn on the led

In3

Low level input will turn on the led

Status

U disk status

Alm

Servo alarm input. Low level input will turn on the led

Clr

Servo alarm clear. Low level input will turn on the led

Zero speed status. Low level input will turn on the led

Son

Low level input will turn on the led

Pulse

Pulse signal indicator. Low level input will turn on the led

Summary of Contents for LFS-PM Series




































Search results

Summary of Contents for LFS-PM Series

Reviews:

Related manuals for LFS-PM Series

Brands by name

Popular brands

Ruida Technology LFS-PM Series, Operating Manual

Search results

Summary of Contents for LFS-PM Series

Reviews:

Related manuals for LFS-PM Series

Brands by name

Popular brands