background image

x

 Safety

6

BA ROTEX GSU - 09/2007

Hydraulic system connection

• When operating the ROTEX GasSolarUnit, especially when using the solar energy, the storage tank temperature can exceed 

60 °C. Protection from scalding (hot water mixing device e.g. VTA32 

 

15 60 16

) should therefore be included when 

installing the system.

Device installation room

• Operate ROTEX GasSolarUnit only if sufficient combustion air supply is ensured. If you operate the ROTEX GSU in ambient-

air-independent mode with an air/ flue gas system (LAS) dimensioned according to ROTEX standard, this is guaranteed 
automatically and there are no further conditions to be met in the device installation room.

• Make sure that there is an opening to the open air for air inlet, of at least 150 cm

2

 if you operate in the ambient air dependent 

mode.

• Do not operate the burner in the ambient air dependent mode in rooms with aggressive vapours (e.g. hair spray, perchloroeth-

ylene, carbon tetrachloride), heavy dust formation (e.g. workshops) or high humidity (e.g. laundries). 

• Always maintain the minimum distances from walls and other objects (see Chapter 7.1).

Operation

• Operate ROTEX GasSolarUnit only with the storage tank filled to overflow.
• Operate ROTEX GasSolarUnit only with closed silencer hoods.

Instruction by the installer

• The handover includes instruction in the operation and control of the ROTEX GasSolarUnit by the installer, using the operating 

instructions.

• Document the handover by filling in and signing the attached installation and instructions form together with the installer.

Disposal

• Through the environmentally-friendly design of the ROTEX GasSolarUnit, ROTEX has complied with the standards for 

environmentally-friendly disposal.

• Proper disposal in compliance with the respective national stipulations of the country of use is the responsibility of the owner.

Documentation

• The technical documentation contained in the scope of supply is part of the device. It must be stored in such a way as to 

ensure that the operator or technical personnel can always refer to it.

Summary of Contents for GSU 320

















































Reviews: