Rose electronics RP2-1R2X16U Installation And Operation Manual Download Page 51 | Manualshive

Page: 51 / 68

Rose electronics RP2-1R2X16U Installation And Operation Manual Download Page 51

ULTRAMATRIX REMOTE INSTALLATION AND OPERATIONS MANUAL

45

When the Viewer successfully connects to the selected locations UltraMatrix Remote, the User must login with a
valid user ID and Password. Enter the User ID assigned and click on “OK”. The Password request box will display.
Enter the assigned password and click on “OK”. There is a 45 second time limit for entering the User ID and
Password. To continue configuring the Viewer, login with the administrator’s User ID (

admin

) and no password.

User ID login

User Password

If the User ID and password are validated on the connected UltraMatrix Remote location, the Viewer will display the
connected computer’s video (if connected and powered on) and a warning dialog box (shown below). Click the “OK”
button to continue. To suppress the warning dialog box from displaying every time a connection is made or the
Viewer is placed in or out of the “Pass-through” mode, click on the check box to suppress the message. To reinstate
the warning dialog box, check “Pass-through warning” on the Help menu.

«
...
49
50
51
52
53
...
»

Summary of Contents for RP2-1R2X16U





































































Reviews:

No comments