manualshive.com logo in svg

Rose electronics RP2-1R2X16U, Installation And Operation Manual, Page: 45 / 68

Share
Download
Rose electronics RP2-1R2X16U Installation And Operation Manual Download Page 45

Viewer Installation 

 

ULTRAMATRIX REMOTE INSTALLATION AND OPERATIONS MANUAL

  

39 

Remote Viewer Installation 

Software Installation 

The Viewer software must be installed on a Windows based workstation connected to the network.  The workstation 
should have the following minimum requirements: 

n

 

133 MHz PC with Microsoft Windows 95 or above 

n

 

32 Mb of system memory 

n

 

4Mb of free disk space 

n

 

VGA display adapter and monitor, capable of 640 x 480 resolution 

n

 

Keyboard and mouse 

n

 

Network connection with TCP/IP protocol 

 
To install the Viewer software, perform the following steps. It is recommended that you close all workstation 
applications before installation. If you are upgrading existing Viewer software or the UltraMatrix Remote firmware, 
please refer to Appendix F & G for upgrade instructions.  
1. Insert the Setup diskette (Diskette #1) and click Start, run, type in A:\Setup.exe in the “Open” input field, click OK.  

the setup wizard (Figure 19) will display.  

2. Click “Next” to begin the installation process. Read the “License agreement” and click “Yes” to continue. 
3. Enter the “Destination directory” if different than the default (C:\Program Files\UltraLink Viewer) and click “Next” 
4. Enter the “Start menu” folder name if different from the default name (UltraLink Viewer) and click “Next”. 
5. Two additional tasks can be performed during installation, create a quick launch icon and create a desktop icon 
6. Check or un-check the choice boxes for the icon’s wanted and click “Next” 
7. A final screen will display. Verify that the “Destination directory”, the “Start menu” folder, and the “Create Icon” 

choices are correct and click “Install”. Click “Back” to correct any information that has been entered incorrectly 

8. The installation process will begin.  Insert Disk 2 when prompted. When the final installation process is completed, 

the finish screen will display. Check the “Launch UltraLink Viewer” box 

9. Click on “Finish” to complete the installation process and launch the Viewer 

 

 

Figure 19. Viewer Set-up Wizard 

 
 
 

Summary of Contents for RP2-1R2X16U





































































Reviews:

No comments