manualshive.com logo in svg

Rose electronics RP2-1R2X16U, Installation And Operation Manual, Page: 43 / 68

Share
Download
Rose electronics RP2-1R2X16U Installation And Operation Manual Download Page 43

 Serial Device Support 

 

ULTRAMATRIX REMOTE INSTALLATION AND OPERATIONS MANUAL

  

37 

Serial device support 

The serial feature is available on the multi-platform models. The serial feature allows you to connect a KVM station to 
a serial device such as the serial port on a Unix or Sun computer, a router or hub, or any compatible serial device. 
The serial device is connected to the DB25F CPU port on the UltraMatrix Remote with a serial cable (See Appendix 
B for serial cable part numbers). Any CPU port can be configured to be a serial port. When you switch to that port, 
you are connected to the serial device and can access it as you normally would.  
 
To configure a CPU port for a serial application, call up the main menu ([Ctrl] – F12), and then select computer and 
press [Enter].  From the configure computer menu, use the up/down arrow keys to select the desired computer to 
configure for serial, then use the left arrow key and select the keyboard field for the selected computer and press 
[Enter].  A selection box will display listing the supported choices.  Use the up/down arrow keys and select the serial 
baud rate to configure the CPU port for and press [Enter].  Save the changes to flash memory.  Once saved, that 
CPU port is configured for serial support.  
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Figure 18. Serial support 

Computer 2 is configured for serial support at 9600 baud. 
 
 
 
 
 
 
 
 

Configure Computer  
 

 

 

 

 

Computer name 

Keyboard 

Mouse  

1  Computer  1 

PC2 

PS/2  

2  Computer   2 

Serial 9600,N,8,1  

3  Computer   3 

PC2 

PS/2  

4  Computer   4 

PC2 

PS/2  

5  Computer   5 

PC2 

PS/2  

6  Computer   6 

PC2 

PS/2  

7  Computer   7 

PC2 

PS/2  

8  Computer   8 

PC2 

PS/2  

9  Computer   9 

PC2 

PS/2  

10  Computer  10 

PC2 

PS/2  

11  Computer  11 

PC2 

PS/2  

12  Computer  12  

PC2 

PS/2  

13  Computer  13 

PC2 

PS/2  

14  Computer  14 

PC2 

PS/2  

15  Computer  15 

PC2 

PS/2  

16  Computer  16 

PC2 

PS/2  

 

 

 

 

Use page up and page down keys to configure more computers,  
Type of computer, for PCs this is the computer’s keyboard mode  

Summary of Contents for RP2-1R2X16U





































































Reviews:

No comments