Ronald 42212TNI Installation Manual Download Page 10 | Manualshive

Page: 10 / 68

background image

10

The approximate maximum power requirements for UFODAS components are:

•

50230UNI-A 30x optical zoom camera

– 23W max.

•

42212TNI 12x optical zoom camera

– 12W

•

NK8BR4 panoramic camera

– 12W

•

N53AB52 bullet camera

– 6W

•

MSDAU

– 4W

•

PowerBeam Ethernet Bridge

– 8.5W

AC power for an Injector and possibly a computer may simply be from a wall-outlet in a
fixed installation or from a portable source such as a DC-to-AC inverter powered by an
automotive 12VDC source or from a solar/battery system.

Sizing a power source for a remote UFODAS installation is based on the total power
required and run time until recharged if battery storage is included.

Thus, for example, the total system power required for a field installation that includes
the panoramic camera, a 50230 camera, an MSDAU and an RF bridge to a remote
router would be 47.5W. Thus, this system could run continuously with a 100W solar
panel during the day and continue during the night using battery storage in the
GoalZero Portable Power Station, shown below. The Power Station provides a 396WH
battery and thus could sustain the 47.5W load for up to about 8 hours without
recharging. Additional 33Ah batteries could be added for longer run times.

The Power Station may be recharged by plugging it into an AC outlet or charged in the
field by means of a 100W (or larger) solar panel, as shown below.

«
...
8
9
10
11
12
...
»

Summary of Contents for 42212TNI





































































Reviews:

No comments

Related manuals for 42212TNI

Brand: Schäfter+Kirchhoff Pages: 32

BluePirat Remote

Brand: Magna Pages: 83

Brand: CamPro Pages: 14

Brand: Zavio Pages: 16

Brand: Braun Pages: 44

X400 Power Pro Series

Brand: GE Pages: 89

Brand: Aspiring Pages: 36

Brand: Oregon Scientific Pages: 17

20MP Waterproof/ Shockproof Digital Camera

Brand: Ivation Pages: 2

Brand: KanDao Pages: 24

GO-5101M-PMCL-1

Brand: JAI Pages: 117

Brand: VESTEL Pages: 76

Brand: hc-cargo Pages: 52

Brand: Ability Pages: 44

Brand: Kaya Instruments Pages: 58

Brand: Rokinon Pages: 2

Brand: GeoVision Pages: 175

CAMEDIA C-360 Zoom

Brand: Olympus Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands