eng eng
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools.
Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired by qualified technical
personnel or an authorised ROLLER service shop before use.
Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to
be performed.
Use of the power tool for operations different from those intended
could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer.
A charger
that is suitable for one type of battery pack may create a risk of fire when used
with another battery pack.
b) Use power tools only with specifically designated battery packs.
Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other small metal objects, that
can make a connection from one terminal to another.
Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
Specific Safety Warnings
WARNING
● Use personal safety equipment (e.g. goggles).
● Avoid unnatural postures, and do not lean too far forward.
● Before changing the pressing or expanding tools, pull the mains plug or take out
the battery!
● The drive units develop a very high pressing force. For that reason, be particularly
careful. Keep all other persons away from the working area during working.
● Hold the drive units only by the housing grip (6) and the pistol grip (9) during opera-
tion. Keep your hands away from moving parts (pressing area, expanding area)!
● Never operate radial presses when the tongs shank (2) is not locked. Risk of fracture!
● Always position radial presses with pressing tong, pressing tong Mini, pressing
ring on the press fitting at a right angle to the pipe axis. Never position it askew.
● Do not start radial presses without pressing tong, pressing tong Mini, pressing
ring inserted. Do not start the pressing operation except to make a press joint.
Unless counter pressure is applied by the press fitting, the drive unit or pressing
tongs, pressing tongs Mini, pressing rings will be needlessly stressed.
● Before using pressing tongs, pressing tongs Mini, pressing rings from other
manufacturers, check that they are suitable for the drive unit. Read and observe
the instruction manuals of the pressing tong or pressing ring manufacturers.
● Only operate axial presses with pressing heads fully inserted. Risk of fracture!
● Always position axial presses with the pressing tongs on the compression sleeve
fitting at right angles to the pipe axis. Never position it askew.
● Screw expanding heads as far as they will go onto the expander.
● Do not attempt to repair damaged pressing tongs, pressing tongs Mini, pressing
rings, adapter tongs, pressing heads or expanding heads. Risk of fracture!
● Consult and comply with the instructions for installation and fitting of the system’s
manufacturers.
● This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
● Only allow trained personnel to use the power tool. Apprentices may only operate
the power tool when they are over 16, when this is necessary for their training
and when they are supervised by a trained operative.
● Ensure the switch is in the off position before inserting battery pack. Inserting
the battery pack into power tools that have the switch on invites accidents.
● Do not use the battery/charger at battery/charger temperatures or ambient
temperatures of ≤ 5°C/40°F or ≥ 40°C/105°F.
● Do not dispose of defective batteries in the normal domestic waste. Take them
to an authorised ROLLER after-sales service facility or to a reputed waste disposal
company.
● Comply with maintenance instructions and instructions on tool replacements.
● Check mains lead of power tool regularly and have it replaced by a qualified
expert or an authorised ROLLER after-sales service facility in case of damage.
Check extension cable regularly and replace it when damaged.
Explanation of symbols
Read the operating instructions
before
use
Power tool complies with protection class I
Power tool complies with protection class II
The tool is not suitable for using outdoors
Environmentally friendly disposal
1. Technical Data
Intended use
WARNING
Use ROLLER’S radial presses only for the intended purpose of making press joints
of all common pressfitting systems.
Use ROLLER’S cropping tongs only for the intended purpose of cropping threaded
bars up to the strength class 4.8 (400 N/mm²).
Use ROLLER’S cable shears only for the intended purpose of cropping electric
cables ≤ 300 mm² (
Ø
30 mm).
Use ROLLER’S axial presses only fort he intended purpose of making compression
sleeve joints and for expanding pipes of all common compression sleeve systems.
Only use ROLLER’S pipe expanders for the intended purpose of expanding and
calibrating pipes.
All other uses are not for the intended purpose and are prohibited.
1.1. Article numbers
ROLLER’S Uni-Press E drive unit
572100
ROLLER’S Uni-Press drive unit
577001
ROLLER’S Uni-Press ACC drive unit
577000
ROLLER’S Multi-Press Mini ACC drive unit Li-Ion
578001
ROLLER’S Multi-Press drive unit Li-Ion
571003
ROLLER’S Multi-Press ACC drive unit Li-Ion
571004
ROLLER’S Axial-Press 25 ACC drive unit Li-Ion
573003
ROLLER’S Axial-Press 25 L ACC drive unit Li-Ion
573004
ROLLER’S Axial-Press 40 drive unit Li-Ion
573006
ROLLER’S Akku-Exparo Cu ACC drive unit Li-Ion
575006
ROLLER’S Akku-Exparo P ACC drive unit Li-Ion
575008
ROLLER’S Akku-Exparo Q & E ACC drive unit Li-Ion
575005
Expanding device 6 – 40 mm, ½ – 1½”
575100
Expanding device 54 – 63 mm, 2”
575101
ROLLER’S battery Li-Ion 14.4 V, 1.6 Ah
571545
ROLLER’S battery Li-Ion 14.4 V, 2.2 Ah
571550
ROLLER’S battery Li-Ion 14.4 V, 3.2 Ah
571555
ROLLER’S voltage supply Li-Ion
571565
Rapid charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
571560
Sheet steel case, ROLLER’S Uni-Press E
570280
Sheet steel case, ROLLER’S Uni-Press
570280
Sheet steel case, ROLLER’S Uni-Press ACC
570280
Sheet steel case, ROLLER’S Multi-Press Mini ACC
578290
Sheet steel case, ROLLER’S Multi-Press /
ROLLER’S Multi-Press ACC
571290
Sheet steel case, ROLLER’S Axial-Press 40
573282
Sheet steel case, ROLLER’S Akku-Exparo Q & E
578290
Sheet steel case, ROLLER’S Axial-Press 25 ACC
and Ax-Press 25 L ACC
573284
Sheet steel case, ROLLER’S Akku-Exparo Cu ACC
573284
Sheet steel case, ROLLER’S Akku-Exparo P ACC
573284
Sheet steel case, Combi Set ROLLER’S Axial-Press 25 ACC
and Akku-Exparo P ACC
573284
1.2. Capacity
ROLLER’S Multi-Press Mini ACC Radial press for making press joints in all
standard press fitting systems on steel pipes, stainless steel
pipes, copper pipes, plastic pipes, composite pipes
Ø 10 – 40 mm
Radial presses ROLLER’S Uni-Press and ROLLER’S Multi-Press for
making press joints in all standard press fitting systems
on steel pipes, stainless steel pipes, copper pipes,
plastic pipes, composite pipes
Ø 10 – 108 mm
Axial presses for making compression sleeve joints (sliding
sleeve joints) on stainless steel pipes, steel pipes, copper
pipes, plastic pipes, composite pipes and for expanding
plastic pipes, composite pipes
Ø 12 – 40 mm
ROLLER’S Akku-Exparo Q & E ACC for expanding of
pipes/coil for the system Uponor Quick & Easy
Ø 16 – 40 mm
Ø ⅜ – 1½”