■
System Realtime Message
*
Following System Realtime Messages cannot be recorded in recording mode.
●
Timing Clock
Status
F8H
*
Recognized only when the “Sync Mode” of the Pattern Global is set at “AUTO”, “EXT”
or “MIDI
➝
DELAY”.
●
Start
Status
FAH
*
Recognized only when the “Sync Mode” of the Pattern Global is set at “AUTO”, “EXT”
or REMOTE.
●
Continue
Status
FBH
*
Recognized only when the “Sync Mode” of the Pattern Global is set at “AUTO”, “EXT”
or REMOTE.
●
Stop
Status
FCH
*
Recognized only when the “Sync Mode” of the Pattern Global is set at “AUTO”, “EXT”
or REMOTE.
●
Active Sensing
Status
FEH
*
When Active Sensing is received, the unit will begin monitoring the intervals of all fur-
ther messages. While monitoring, if the interval between messages exceeds about 420
ms, the same processing will be carried out as when All Sounds Off, All Notes Off and
Reset All Controllers are received, and message interval monitoring will be halted.
■
System Exclusive Message
*
Following System Exclusive Messages cannot be recorded.
Status
Data byte
Status
F0H
iiH, ddH, ......,eeH
F7H
F0H:
System Exclusive Message status
ii = ID number:
an ID number (manufacturer ID) to indicate the manufacturer whose
Exclusive message this is. Roland’s manufacturer ID is 41H.
ID numbers 7EH and 7FH are extensions of the MIDI standard;
Universal Non-realtime Messages (7EH) and Universal Realtime
Messages (7FH).
dd,...,ee = data:
00H - 7FH (0 - 127)
F7H:
EOX (End Of Exclusive)
The System Exclusive Messages received by the TD-10 are; Universal Non-realtime System
Exclusive Messages, Data Requests (RQ1), and Data Set (DT1).
●
Universal Non-realtime System Exclusive Messages
❍
Inquiry request
Status
Data byte
Status
F0H
7EH, dev, 06H, 01H
F7H
Byte
Explanation
F0H
Exclusive status
7EH
ID number (universal non-realtime message)
dev
Device ID (dev: 00H - 1FH (1 - 32) Initial value is 10H (17))
06H,01H
Inquiry request
F7H
EOX (End Of Exclusive)
*
Even if the Device ID is 7FH (Broadcast), Inquiry Reply message will be transmitted.
*
When Inquiry Request is received, Inquiry Reply message will be transmitted.
●
Data transmission
TD-10 can transmit and receive the various parameters using System Exclusive messages.
The exclusive message of TD-10’s data has a model ID of 00H 0AH and a device ID of 10H
(17). Device ID can be changed in TD-10.
❍
Request data 1
RQ1 (11H)
This message requests the other device to send data. The Address and Size determine the
type and amount of data to be sent.
When a Data Request message is received, if the device is ready to transmit data and if the
address and size are appropriate, the requested data will be transmitted as a “Data Set 1
(DT1)” message. If not, nothing will be transmitted.
Status
Data byte
Status
F0H
41H, dev, 00H, 0AH, 11H, aaH, bbH, ccH, ddH,
F7H
ssH, ttH, uuH, vvH, sum
Byte
Explanation
F0H
Exclusive status
41H
ID number (Roland)
dev
Device ID (dev: 00H - 1FH Initial value is 10H (17))
00H 0AH
Model ID (TD-10)
11H
Command ID (RQ1)
aaH
Address MSB: upper byte of the starting address of the requested data
bbH
Address 2nd : 2nd byte of the starting address of the requested data
ccH
Address 3rd : 3rd byte of the starting address of the requested data
ddH
Address LSB: lower byte of the starting address of the requested data
ssH
Size MSB
ttH
Size 2nd
uuH
Size 3rd
uuH
Size LSB
sum
Checksum
F7H
EOX (End Of Exclusive)
*
The amount of data that can be transmitted at once time will depend on the type of
data, and data must be requested using a specific starting address and size. Refer to the
Address and Size listed in Parameter Dump Request (Page 158).
*
Regarding the checksum please refer to Page 163.
❍
Data set 1
DT1 (12H)
This is the message that actually performs data transmission, and is used when you wish to
transmit the data.
Status
Data byte
Status
F0H
41H, dev, 00H, 0AH, 12H, aaH, bbH, ccH, ddH,
F7H
eeh,... ffH, sum
Byte
Explanation
F0H
Exclusive status
41H
ID number (Roland)
dev
Device ID (dev: 00H - 1FH Initial value is 10H))
00H
0AH Model ID (TD-10)
12H
Command ID (DT1)
aaH
Address MSB: upper byte of the starting address of the transmitted data
bbH
Address 2nd : 2nd byte of the starting address of the transmitted data
ccH
Address 3rd: 3rd byte of the starting address of the transmitted data
ddH
Address LSB: lower byte of the starting address of the transmitted data
eeH
Data: the actual data to be transmitted. Multiple bytes of data are transmitted
starting from the address.
:
:
ffH
Data
sum
Checksum
F7H
EOX (End Of Exclusive)
*
The amount of data that can be transmitted at once time will depend on the type of
data, and data must be requested using a specific starting address and size. Refer to the
Address and Size listed in Parameter Dump Request (Page 158).
*
If “Data Set 1” is transmitted successively, there must be an interval of at least 45 ms.
*
Regarding the checksum please refer to Page 163.
MIDI implementation
156
Summary of Contents for V-DRUMS TD-10
Page 21: ...Quick Start Quick Start 21...
Page 131: ...Appendices Appendices 131...
