Roland juno-ds61, Parameter Manual

Page: 24 / 88

24
Performance Mode
Effects Parameters
COMMON
Parameter Value/Explanation
MFX Structure
Specify how MFX1–3 will be connected.
TYPE01
MFX1
MFX2
MFX3
TYPE02
MFX1
MFX3
MFX2
TYPE03
MFX1
MFX2
MFX3
TYPE04
MFX1
MFX2 MFX3
TYPE05
MFX2
MFX3
MFX1
TYPE06
MFX2
MFX3 MFX1
TYPE07
MFX1
MFX3 MFX2
TYPE08
MFX1
MFX2
MFX3
TYPE09
MFX2
MFX3
MFX1
TYPE10
MFX1
MFX3
MFX2
TYPE11
MFX1 MFX2 MFX3
TYPE12
MFX1 MFX3 MFX2
TYPE13
MFX2 MFX3 MFX1
TYPE14
MFX2 MFX1 MFX3
TYPE15
MFX3 MFX1 MFX2
TYPE16
MFX3 MFX2 MFX1
MFX1–3 Source
Selects the MFX parameter settings that will be used by the performance.
PERFORM
Use the MFX settings of the performance
UPPER (PART1),
LOWER (PART2),
PART3–16
Use the MFX settings of the patch or drum kit assigned
to the specified part
Chorus Source
Selects the chorus parameter settings that will be used by the
performance.
PERFORM
Use the chorus settings of the performance
UPPER (PART1),
LOWER (PART2),
PART3–16
Use the chorus settings of the patch or drum kit
assigned to the specified part
Reverb Source
Selects the reverb parameter settings that will be used by the
performance.
PERFORM
Use the reverb settings of the performance
UPPER (PART1),
LOWER (PART2),
PART3–16
Use the reverb settings of the patch or drum kit
assigned to the specified part
MFX1–3
Parameter Value/Explanation
MFX Type
Turns MFX on/off, and specifies the type of MFX that is used. If MFX is on,
8 shows a “
(
” mark.
* For details on MFX parameters, refer to “MFX Parameters (MFX,
MFX1–3)” (p. 40).
00: THRU–80: BIT CRUSHER
Parameters for
each MFX type Edit the parameters of the MFX type you’ve selected.
* Refer to “MFX Parameters (MFX, MFX1–3)” (p. 40).
Chorus Send Level
Specifies the level of the signal sent to the chorus.
0–127
Reverb Send Level
Specifies the level of the signal sent to the reverb.
0–127
MFX1–3 CTRL
Parameter Value/Explanation
Source 1–4
Sets the MIDI message used to change the MFX parameter with the MFX
control.
OFF
MFX control will not be used.
CC01–31, 33–95 Controller numbers 1–31, 33–95
PITCH BEND Pitch bend
AFTERTOUCH Aftertouch
SYS CTRL1–4 Use the System Control 1–4 Source setting (p. 34).
Destination 1–4
Sets the MFX parameters to be controlled with the Source1–4. The MFX
parameters available for control will depend on the MFX Type.
* Refer to “MFX Parameters (MFX, MFX1–3)” (p. 40).
Sens 1–4
Specifies the depth of MFX control.
Specify a positive (+) value if you want to change the value of the assigned
destination in a positive direction (larger, toward the right, faster, etc.), or
specify a negative value (-) if you want to change the value in a negative
direction (smaller, toward the left, slower, etc.).
Larger values will allow a greater amount of control.
-63–+63
CHORUS
Parameter Value/Explanation
Chorus Type
Turns Chorus on/off, and specifies the type of chorus that is used. If Chorus
is on, 8 shows a “
(
” mark.
00: OFF Neither chorus or delay is used.
01: CHORUS Chorus is used.
02: DELAY Delay is used.
03: GM2 CHORUS GM2 chorus
Parameters for
each chorus type
Set the parameters of the selected chorus type. The chorus parameters
available for control will depend on the Chorus Type.
* Refer to “Chorus Parameters” (p. 58).
Output Select
Specifies how the sound routed through chorus will be output.
MAIN
Output to the OUTPUT jacks in stereo.
REV Output to reverb in mono.
M+R
Output to the OUTPUT jacks in stereo, and to
reverb in mono.
Chorus Level
Adjusts the volume of the sound that has passed through chorus.
0–127
REVERB
Parameter Value/Explanation
Reverb Type
Turns Reverb on/off, and specifies the type of reverb that is used. If Reverb
is on,
8
shows a “
(
” mark.
00: OFF Reverb is not used.
01: REVERB Normal reverb
02: SRV ROOM
This reverb simulates typical room acoustic
reflections.
03: SRV HALL
This reverb simulates typical concert hall acoustic
reflections.
04: SRV PLATE
This reverb simulates a reverb plate, a popular
type of artificial reverb unit that derives its sound
from the vibration of a metallic plate.
05: GM2 REVERB GM2 reverb
Parameters for
each reverb type
Set the parameters of the selected reverb type. The reverb parameters
available for control will depend on the Reverb Type.
* Refer to “Reverb Parameters” (p. 58).
Reverb Level
Adjusts the volume of the sound that has passed through reverb.
0–127