21
Performance Mode
Part Edit
MEMO
5
PART EDIT and PERFORMANCE EDIT have the same parameters in common.
5
If you’re using the pattern sequencer, the part edit settings are saved as a “pattern.”
Procedure
1 .
Press the [PATCH/PERFORM] button to make it light.
2 .
Select a performance that you want to edit.
3 .
Press the [SAMPLE IMPORT] button and [DAW CONTROL] button
simultaneously.
The EDIT MENU screen appears.
4 .
Move the cursor to “PART EDIT,” and press the [ENTER] button.
The PART EDIT screen appears.
MEMO
5
In the PART EDIT screen, you can use pads [1]–[8] to select the part that you
want to edit. If you hold down the [SHIFT] button and press a pad [1]–[8], a part
9–16 is selected.
5 .
Move the cursor to tab, and use the [
K
] [
J
] buttons to switch the pages.
6 .
Move the cursor to the parameter that you want to edit, and use the value
dial to change the value.
7 .
To save the edited settings, perform the operation “Saving Your Settings
(Write)” (refer to owner’s manual).
Performance Parameters
PATCH
Parameter
Value/Explanation
TYPE
Sets the assignment of a patch (Patch) or drum kit (Drum) to each of the
parts.
Patch, Drum
BANK
Selects the group to which the desired patch or drum kit belongs.
DS (DS tone), PRST (Preset), GM (GM2 tone), EXP (expansion sounds), USER
Category number
Selects the desired patch or drum kit by its number.
0001–
LEVEL/CH
Parameter
Value/Explanation
Solo Switch
Turns on the part that you want to solo. Parts other than the soloed part
are not heard.
OFF, ON
Mute Switch
Specifies whether each part’s performance is temporarily muted (ON) or
not muted (OFF).
*
The Mute parameter does not turn the part off; it mutes the sound by
minimizing the volume. Therefore, the part still receives MIDI messages.
OFF, ON
Level
Adjust the volume of each part. This setting’s main purpose is to adjust the
volume balance between parts.
0–127
Pan
Adjust the pan of each part. “L64” is far left, “0” is center, and “63R” is far
right.
L64–0–63R
Rx Switch
For each part, specify whether MIDI messages will be received (ON), or not
(OFF).
If this is “OFF,” the part will not respond. Normally, you should leave this
“ON,” but you can turn it “OFF” when you do not want a specific part to be
playing during song playback.
OFF, ON
Rx Channel
Specifies the MIDI receive channel for each part.
*
You can’t edit this parameter if the [PATTERN SEQUENCER] button is lit.
1–16
OUTPUT
Parameter
Value/Explanation
Output Assign
Specifies for each part how the direct sound will be output.
MFX
Output in stereo through MFX. You can also apply chorus or
reverb to the sound that passes through MFX.
L+R
Output to the OUTPUT L (MONO) jack and OUTPUT R jack in
stereo without passing through MFX.
L, R
Output to the OUTPUT L (MONO) jack or OUTPUT R jack in
mono without passing through MFX.
PAT
Outputs according to the settings for patch.
Output MFX Sel
Of the three types of MFX that can be used simultaneously, specify which
MFX will be used.
1–3 (MFX1–MFX3)
Output Level
Set the level of the signal that is sent to the output destination specified
by Part Output Assign.
0–127
Cho Send Level
Sets the level of the signal sent to chorus for each part.
0–127
Rev Send level
Sets the level of the signal sent to reverb for each part.
0–127
PITCH
Parameter
Value/Explanation
Octave Shift
Adjusts the pitch of the part’s sound up or down in units of an octave (±3
octaves).
*
Note that when a rhythm set is assigned to a part, you cannot modify
the Octave Shift.
-3–+3
Coarse Tune
Adjusts the pitch of the part’s sound up or down in semitone steps (±4
octaves).
-48–+48
Fine Tune
Adjusts the pitch of the part’s sound up or down in 1-cent steps (±50
cents).
-50–+50
Mono/Poly
Set this parameter to “MONO” when the patch assigned to the part is to
be played monophonically, or to “POLY” when the patch is to be played
polyphonically. If you want to use the Mono/Poly setting of the patch
assigned to the part (p. 5), set this to “PAT.”
*
This setting is ignored for parts to which a drum kit is assigned.
MONO, POLY, PAT
Legato Switch
Turn this parameter “ON” when you want to use the Legato feature and
“OFF” when you don’t. If you want to use the Legato Switch setting of the
patch assigned to the part (p. 5), set this to “PAT.”
*
This setting is ignored for parts to which a drum kit is assigned.
OFF, ON, PAT
Bend Range
Specifies the amount of pitch change in semitones (2 octaves) that will
occur when the Pitch Bend Lever is moved. The amount of change when
the lever is tilted is set to the same value for both left and right sides. If you
want to use the Pitch Bend Range setting of the patch assigned to the part
(p. 7), set this to “PAT.”
0–24, PAT
Porta Switch
Turn this parameter “ON” when you want to apply Portamento and “OFF”
when you don’t. If you want to use the Portamento Switch setting of the
patch assigned to the part (p. 5), set this to “PAT.”
OFF, ON, PAT
Porta Time
When portamento is used, this specifies the time over which the pitch
will change. Higher settings will cause the pitch change to the next note
to take more time. If you want to use the Portamento Time setting of the
patch assigned to the part (p. 5), set this to “PAT.”
*
This setting is ignored for parts to which a drum kit is assigned.
0–127, PAT
